Open Sesame Door Systems 133 Installation Manual
Hide thumbs
Also See for 133:
- Owner's manual (19 pages) ,
- Installation manual booklet (22 pages) ,
- Owner's manual (21 pages)
Related Manuals for Open Sesame Door Systems 133
Summary of Contents for Open Sesame Door Systems 133
- Page 1 INSTALLATION GUIDE Open Sesame Door Systems, Inc. Manufacturer of Disability Access products 1.800.673.6911 PLEASE KEEP THIS GUIDE FOR FUTURE INSTALLATIONS...
- Page 2 Thank you for your purchase of the Open Sesame Automatic Door System. This product is designed to be durable and provide years of reliable service. To ensure the Open Sesame Door System lives up to all expectations, it is important to read and comply with this installation guide.
-
Page 3: Table Of Contents
Model 133 Diagram . . . . . . . . . . . . . . . . . . . -
Page 4: Recommended Tools For Installation
RECOMMENDED TOOLS FOR INSTALLATION Ladder or Step stool Tape measure Voltmeter (for troubleshooting) Phillips #2 Screwdriver 5/32” or 4mm Allen wrench Wire Cutters Wire Strippers Oscillating Multi Tool (recommended for Strike Installation) Loctite (for arm screw if removed) 10 . Drill/Driver with #2 & #3 Phillips Bits... -
Page 5: What You Will Find In The Box
WHAT YOU WILL FIND IN THE BOX: 1 . Door operator with wiring kit and wall transformer 2 . Remote Control(s) – if required 3 . Electric Strike(s) & Strike Tester – if required - For Electric Strike Installation, refer to separate instructions included with the strike 4 . -
Page 6: Selecting Mounting Format/Left Hand Conversion
SELECTING THE CORRECT MOUNTING FORMAT *ALL DOORS DISPLAYED ARE VIEWED FROM THE INSIDE* OPTION A: DOOR MOUNT OPTION B: LINTEL MOUNT DOOR DOOR OPENS OPENS INWARD OUTWARDS LEFT SIDE HINGES RIGHT SIDE HINGES LEFT SIDE HINGES RIGHT SIDE HINGES OPTION C: PARALLEL MOUNT SAFETY NOTE: OUTSWING Secure door before... -
Page 7: Electric Strike/M233 Clutch Adjustment
ELECTRIC STRIKE (ADAMS RITE ONLY) If an electric strike is used, follow the instruc- tions included in the packaging from the electric strike manufacturer to assemble the strike and install it in the door jamb. STRIKE SETTING Adam Rite 7440 Electric Strikes are provided in the “fail secure”... -
Page 8: Door Mount Instructions (Option A)
On the door measure 3” away from the hinges for position the operator and screw into position. Model 133 and 4” for Model 233, then create a mark. Remove molding for flush mounting against This is where the operator will need to be positioned. - Page 9 ARM13” Line up the arm with marking you did on the door jamb so that the middle of the shoe is position where With the door closed, adjust the arm to 90 degrees. the mark is, then screw into place. Do NOT mount arm shoe too high above operator because it will cause binding of joints leading to screws falling off.
-
Page 10: Lintel Mount Instructions (Option B)
DOOR ” 13” Note: Position Model 133 at 3” and Model 233 at 4” away from hinges and mount arm at 13” from hinges. Mount arm shoe 1 “ down from top of the door. After mounting unit, see page 9 and review instructions on inside cover. -
Page 11: Parallel Mount Diagram (Option C)
OPERATOR 4” - 6” away from hinges. (to find the location of the switch, see diagrams for Model 133/233 on pages 19 & 20) TYPICAL RESIDENTIAL TYPICAL COMMERCIAL PARALLEL MOUNT FOR PARALLEL MOUNT FOR... -
Page 12: Residential Installation Wiring Diagram
RESIDENTIAL INSTALLATION WIRING DIAGRAM USING SUPPLIED WIRING KIT (for applications without electric strikes, remove green/yellow wires from telephone jack) ELECTRIC STRIKE CONNECTION: GREEN & YELLOW ON JACK (YELLOW IS +, GREEN IS -) WIRE TO RJ-11 TELEPHONE JACK BE RUN ON SURFACE MOUNTED SURFACE, OR RECESSED... -
Page 13: French Door-One Operator Diagram
STRIKE WIRING FRENCH DOOR WITH ONE OPERATOR, ONE ELECTRIC STRIKE (pre-wired kit) RJ-11 JACK #1 RJ-11 JACK #2 RJ-11 JACK #3 RED & BLACK WIRE PAIR ELECTRIC STRIKE POWERED BY OPERATOR POWER OUTLET FIXED MOVEABLE DOOR DOOR TRANSFORMER 24VAC NO POLARITY INSTALLATION GUIDE... -
Page 14: French Door -Two Operators-Two Strikes Diagram
POWER WIRING - DOUBLE DOOR WITH TWO OPERATORS, TWO ELECTRIC STRIKES RJ-11 JACK RJ-11 JACK POWER OUTLET 24VAC 24VAC TRANSFORMER TRANSFORMER NOTE: IF NECESSARY, ONE TRANSFORMER CAN BE USED TO SUPPLY POWER TO BOTH UNITS... -
Page 15: Functionality Adjustments
ADJUSTMENTS Your Open Sesame door operator has three potenti- ometers (pots/knobs) adjustments and one position jumper adjustment (auto-close). To change these set- tings at any point during or after installation you must first remove the Operator cover. The location of these adjustments are shown on the diagram on the inside cover of the operator. -
Page 16: Model 233 Clutch Adjustment
CLUTCH ADJUSTMENT (MODEL 233 ONLY) Adjust force applied to door during manual door opening, as well as powered opening. Can adjust for stronger force, for increased wind resistance for outward opening door, lighter for easier opening if stronger force not needed. Simply adjust Red Ring on clutch. - Page 17 REMOTE CONTROL PROGRAMING INSTRUCTIONS All current 433 MHz units with green (or green tipped) antenna wire Standard Remote Control Transmitter PROGRAM This transmitter is a visor transmitter which BUTTON may be mounted below the wheelchair armrest or a side panel. A sensitivity paddle is included to make it easier to push.
-
Page 18: Programming Instructions For Remote Controls Erasing All Transmitter Codes
CONTINUED REMOTE CONTROL PROGRAMING INSTRUCTIONS TO ERASE ALL TRANSMITTER CODES: 1. Press and then release the receiver programming button five times quickly (within 3 sec. time). 2. The light will flash 5 times, indicating that ALL remotes have been erased from the receiver memory. If you have problems programming, there is a green indicator light that can be observed inside the unit with the cover off, that can be used for troubleshooting. -
Page 19: Troubleshooting
TROUBLESHOOTING ISSUE CAUSE SOLUTION No Green (ON) No power from transformer Check outlet for Proper Voltage light on the (no green light on the transformer) board Wires disconnected from Check connection to the transformer transformer Bad Transformer Replace transformer No red light Operator is switched OFF Move switch to ON position on board... - Page 20 TROUBLESHOOTING CONTINUED ISSUE CAUSE SOLUTION Door moves slower Weather stripping, Remove anything that might be upon opening/closing dragging on door . dragging the door . Thick weather stripping may need to be removed. Battery Failure Recharge or replace battery Strike does not release Clutch is engaging and Battery Failure-Turn off operator and door latch...
-
Page 21: Model 133 Diagram
MODEL 133 System should be mounted 3” away from hinges (edge of door) Arm should be mounted 13” from hinge PARTS: ADJUSTMENTS: 8 . (on top of the unit) Sensor “H” (senses the Test(Blk) and Program(Red) Buttons magnet under red dot;... -
Page 22: Model 233 Diagram
MODEL 233 System should be mounted 4” away from hinges (edge of door) Arm should be mounted 13” from hinge Additional accessory bumper can be included If needed. PARTS: ADJUSTMENTS: Sensor “H” (senses the 8 . (on top of the unit) magnet under red dot;...
Need help?
Do you have a question about the 133 and is the answer not in the manual?
Questions and answers