Sealey EH3001 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Indoor Use
Instruction Only
Manual
This product is only suitable for well insulated areas or occasional use.
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
‰
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We
also recommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are
plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual
Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for
the safe condition of those appliances and the safety of the appliance operators.
If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it
to the power supply. See 1.1.1. and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none are loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
8
item repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is
8
damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected that the cable outer insulation
extends beyond the cable restraint and that the restraint is tight.
Double insulated products, which are always marked with this symbol
DO NOT connect either wire to the earth terminal.
8
1.1.7. Products which require more than 13amps are supplied without a plug. In this case you must contact a qualified electrician
to ensure that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin
plug and socket with your electrician.
1.1.8. If an extension reel is used it should be as short as possible and fully unwound before connection. A reel with an RCD fitted is
preferred since any appliance plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but
to be absolutely sure that the capacity of the reel is suitable for this product and for others which may be used in the other output
sockets, we recommend the use of 2.5mm² section cable.
1.2. GENERAL SAFETY
‰ ‰ WARNING!‰Disconnect the heater from the mains power supply, before servicing or performing any maintenance. Servicing or
‰
‰
maintenance must only be carried out by an authorised service agent.
‰ ‰ Check that the heater is in sound condition and good working order. Take immediate action to repair or replace damaged parts.
9
‰
‰ ‰ Use recommended parts only. Unapproved parts may be dangerous and will invalidate the warranty.
9
‰
‰ ‰ Position the heater at least a minimum of 0.5mtr at the rear and sides, and 2mtr at the front, from any walls or objects.
9
‰
‰ ‰ WARNING! DO NOT use the heater near flammable material, liquids, solids, gases or compressed gas cylinders etc.
‰
‰
‰ ‰ DO NOT obstruct the air inlet and outlet sections of the heater.
‰ 8
‰ ‰ DO NOT cover the heater.
‰ 8
© Jack Sealey Limited
INDUSTRIAL FAN HEATER 3KW 2 HEAT
SETTINGS
EH3001
MODEL NO:
Original Language Version
THIS PRODUCT REQUIRES A ROUND PIN 16A PLUG.
WE RECOMMEND THAT YOU
DISCUSS THE INSTALLATION OF
AN INDUSTRIAL ROUND PIN
PLUG AND SOCKET WITH A
QUALIFIED ELECTRICIAN.
, are fitted with live (brown) and neutral (blue) wires only.
EH3001| Issue: 6(ERP) - 20/06/18
RECOMMENDED
FUSE RATING - 16A