Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for TruGolf VISTA Series
Summary of Contents for TruGolf VISTA Series
- Page 1 VISTA 12 & VISTA 10 INSTALLATION GUIDE...
- Page 2 Congratulations on your purchase of a TruGolf simulator! We are cords, power supplies before use. If the product is damaged DO NOT thrilled to have you as part of our team. Throughout the years, TruGolf’s USE and contact TruGolf. simulators have been used in country clubs, training facilities, sports •...
- Page 3 ANY DAMAGE OR INJURY CAUSED BY FAILURE TO FOLLOW THESE or lack of experience and knowledge, without supervision GUIDELINES. IN NO EVENT WILL TRUGOLF BE LIABLE FOR ANY and instruction concerning use of the simulator by a person SPECIAL, INCIDENTAL, PUNITIVE OR CONSEQUENTIAL DAMAGES responsible for their safety.
-
Page 4: Table Of Contents
We suggest you watch a few videos before or during setup to help you Setup Assistance ................ 1 assemble your Vista 12 or Vista 10 Golf Simulator. Frame Diagram ................2 Visit: https://trugolf.com/vista-setup Assemble Frame ................ 4 Enclosure ..................8 Wiring ..................13 Computer Components Diagram ..........16 Overhead Light Instructions ...........18... -
Page 5: Frame Diagram
TRUGOLF VISTA 10/12 FRAME DIAGRAM Note: The Vista 12 and Vista 10 frame’s assemble the same with the exception of several smaller frame pieces on the Vista 10. These include: 2,5,7,9,12,15,17,19,G,K, & M. -
Page 6: Assemble Frame
TRUGOLF VISTA 10/12 ASSEMBLE FRAME STEP 4 | TOP CORNER PIECES Assemble the top portion of the frame. Connect [C] & [D] to the sides, then insert the top frame pieces between [C] & [D] as shown below. STEP 1 | CORNER PIECES Tip: To make assembling the frame top easier, tip the frame forward and lay it Start assembling the frame with the back corner pieces labeled [A] &... - Page 7 TRUGOLF VISTA 10/12 STEP 7 | SIDES AND TOP Assemble the walls as shown below. Attach the remaining bungee cord to the frame. Start from the center moving out to the corners. Stretch bungee cord up and onto the INSIDE KNOBS to create a zigzag pattern.
-
Page 8: Enclosure
TRUGOLF VISTA 10/12 ENCLOSURE STEP 2 | TOP BUNGEES Once the top sides have been attached, continue securing the enclosure back edge to the frame using the integrated bungee system. STEP 1 | TOP TIP: This is done in a similar fashion used to attach the screen. - Page 9 STEP 3 | AWNING Attach the TRUGOLF BANNER to the top front edge of the simulator using the integrated Velcro. Start at the middle of the banner, attaching it around the LIGHT BAR [Q], then move towards the sides.
-
Page 10: Wiring
TRUGOLF VISTA 10/12 WIRING STEP 4 | SIDE BAFFLES Attach the SCREEN BAFFLES to the SIDE WALLS using the integrated Velcro. STEP 1 | CABLES First, run SERIAL CABLE and VIDEO CABLE under the TURF and HITTING PLATFORM to the center cutout. (SERIAL CABLE will be connected to the COMPUTER later.) - Page 11 STEP 5 | PROJECTOR COVER Plug COVER FANS into POWER STRIP. Place COVER over projector. NOTE: Do Not scratch projector lens with projector cover. TruGolf will not replace projectors with scratched lens. STEP 3 | HITTING MAT Connect the RIBBON CABLE on the HITTING MAT to the TRUTRACK CONTROL BOX.
-
Page 12: Computer Components Diagram
TRUGOLF VISTA 10/12 COMPUTER COMPONENTS DIAGRAM Connect USB Devices to any available USB PORT. Connect MONITOR • Mouse to COMPUTER using • Keyboard both a USB and DVI CONNECTION TO CLONE IMAGE ON DISPLAYS SEE PG 19 Connect COMPUTER to PROJECTOR using HDMI or other available CONNECTION. -
Page 13: Overhead Light Instructions
TRUGOLF VISTA 10/12 OVERHEAD LIGHT INSTRUCTIONS CLONE DISPLAYS There are two methods to set up multiple monitors in Windows 7. Make INSTALLATION sure that you connect the external monitors to your laptop or your desktop 1. Push the top portion of the head adapter into the slot of the track computer first. -
Page 14: Ball Placement: Full Shots
TRUGOLF VISTA 10/12 BALL PLACEMENT: FULL SHOTS TROUBLESHOOTING DRIVER, WOODS, HYBRIDS & IRONS ERROR MESSAGE “No TruTrack system was found. Please ensure the system is plugged in.” Do the following: 1. Check all connections on TruTrack Hitting Mat. 2. Check that the TruTrack Power and Ground Cables are plugged in. -
Page 15: Diagnostics
TRUGOLF VISTA 10/12 DIAGNOSTICS ACOUSTIC SENSORS There are three acoustic ball impact sensors (see page 13). Tap each sensor To run Diagnostics: to verify each one is connected correctly. A sensor may be unresponsive if: 1. Open E6 CONNECT. 1. Microphone is not connected to the cable. - Page 16 TRUGOLF VISTA 10/12 NOTES NOTES...
- Page 17 TRUGOLF .COM #DRIVINGREALITY #GOLFCONNECTED...
Need help?
Do you have a question about the VISTA Series and is the answer not in the manual?
Questions and answers