Advertisement
1
4xB
3
4xB
C
C
Tools required: Drill driver, PHILLIPS bit PH2. Hex key 4mm and 5mm.
*** For technical support please call 1.800.374.7438 #2007, servicetech@sisergo.com ***
2
A
A
4xB
3
4xB
C
A x 2 (m8x12)
R011065
Elle Series
Components Required:
1. Leg upright x2
2. Adjustable Crossbar x1 (3 Pieces)
3. L Brackets x2
4. Control box x1
5. Control switch x1
6. 120v Power Cord x1
7. Network Cable x4
8. Cable tray x1 (Optional)
9. Hardware Bag x1
10. Battery Pack x1 (Optional)
1
11. DC Cable with 2-pole minift plug x1 (Optional)
12. Hook & Loop (150mm) x2
13. Hook & Loop (350mm) x1
Assembly Steps:
1. Attach leg uprights(1) to ends of adjustable
crossbar (2) and L-brackets(3) with four M8x20mm
machine screws (B) per component.
2. Attach adjustable crossbar center(2) to
adjustable crossbar ends with two M8x12mm
machine screws(A).Set the spacing for the
adjustable crossbar(2) so that the overall width of
C
the frame corresponds with the overall width of the
table top to be mounted
NOTE: Depending on frame model, table may not
include optional cable managemet tray (8). If not,
skip to step 6 on page 3.
B X 16 (m8X20)
C x 4
R011009
RM-175
Page: 1 of 5
4-Leg Electric
4mm HEX WRENCH
5mm HEX WRENCH
R011921
R011905
Advertisement
Table of Contents
Related Manuals for SIS Ergo Elle Series
Summary of Contents for SIS Ergo Elle Series
- Page 1 Page: 1 of 5 Elle Series 4-Leg Electric Components Required: 1. Leg upright x2 2. Adjustable Crossbar x1 (3 Pieces) 3. L Brackets x2 4. Control box x1 5. Control switch x1 6. 120v Power Cord x1 7. Network Cable x4 8.
- Page 2 Page: 2 of 5 Elle Series 4-Leg Electric Optional Cable Tray Assembly: 3. Mounting Cable Tray: The cable tray (8) can be locked into the inside frame rail of the leg uprights (1). Extend out the machine screw locks on either end of...
- Page 3 Page: 3 of 5 Elle Series 4-Leg Electric 5. Attach adjustable crossbar ends(2) to worksurface using two M5x50mm wood screws(F), and adjustable crossbar center(2) to the worksurface using fourteen M5x25mm wood screws(D). 6. Attach L-Brackets to worksurface using six M5x25mm wood screws(D) 7.
- Page 4 Page: 4 of 5 Elle Series 4-Leg Electric 9. Place control box (4) in cable tray. 10. Connect a network cable (7) to the control box (4) and then to each network cable port exiting the leg uprights (1). 11. Connect control switch cable(5) and power cable (6) to the control box(4), and then power cord (6) to 120v power outlet.
- Page 5 Page: 5 of 5 Elle Series 4-Leg Electric Optional Battery Pack Installation 14. Place battery pack (10) in cable tray. NOTE: For frame models that do not utilize a cable tray mount battery pack (10) to underside of worksurface using two 10mm screws.
Need help?
Do you have a question about the Elle Series and is the answer not in the manual?
Questions and answers