Page 1
LH01796:12/00 Legacy.p65 Single Dropside Crib/Daybed & 21711 Drawer with Hidden Hardware Factory Installed CHILD CRAFT INDUSTRIES, INC. P.O. Box 444, Salem, IN USA 47167-0444 PH: 812-883-3111 - FAX: 812-883-1819 - http://www.childcraftind.com ASSEMBLY DIRECTIONS PARTS LIST Φ Φ Φ Φ Φ READ ALL INSTRUCTIONS WITH CARE BEFORE STARTING THE ASSEMBLY PROCEDURE.
Page 2
LH01796:12/00 PARTS ENCLOSED IN CARTON: (1) Spring (1) Stabilizing Bar (attached to Spring W ) Plastic Pouch (1) Dropside wide rail on each (1) Footboard (1) Headboard (style may vary) (style may vary) conceals Hidden Hardware (1) Stationary Side (2) Drawer Rails (1) Drawer Bottom (1) Drawer Partition (1) Drawer Back...
Page 3
LH01796:12/00 Mount End Plate-Right N and End Plate-Left M to ends of Stabilizing Bar V 1 - D 1: S IAGRAM TABILIZING SSEMBLY using (4) Pan Head Machine Screws I and (4) Lock Nuts G exactly as shown. IMPORTANT: End Plates must be positioned in the correct mounting holes in the Stabilizer Bar exactly as illustrated.
Page 4
LH01796:12/00 3- D 3: A & F IAGRAM TTACH TABILIZING AR TO EADBOARD OOTBOARD Insert a Slotted/Phillips Machine Screw A into the top threaded NOTE: Drawer Rails installed during Step 2 are not shown in this diagram for clarity. insert, located in the large routed circle, on both the Footboard Z and Headboard...
Page 5
LH01796:12/00 5 - D 5: I IAGRAM NSTALLATION OF ROPSIDE PREPARATION FOR INSTALLATION OF DROPSIDE: II. Engagement of Loosen the four Slotted/Phillips Screws A which attach Metal Top Track the Stabilizing Bar V to the Headboard A A and Footboard and Upper Guide Z to prepare for Dropside X installation.
Page 6
LH01796:12/00 6- D 6: S IAGRAM PRING SSEMBLY Install (4) Spring Mounting Brackets B to ends of Spring using (8) Pan Head Ma- chine Screws I and (8) Lock Nuts G , (metal threads of Lock Nut to be inserted first over Screw as shown in EN- LARGED VIEW.) Tighten all (8) Pan Head Ma-...
Page 7
LH01796:12/00 8 - D 8: D & I Installation of Mini Blocs C C. Refer to Diagrams 8A, 8B, 8C, 8D, and IAGRAM RAWER UILD NSTALLATION 8E. Install (1) Mini Bloc C C into each of the Drawer Ends F F as shown in Diagram 8A.
Page 8
BE USED TO CLEAN THIS FINE FURNITURE. •STORAGE AND USE OF YOUR LEGACY CRIB: A printed plastic pouch is attached to the crib spring for the permanent storage of the assembly directions. After completing the assembly process you are advised to read and be aware of all WARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND MAINTENANCE notices contained in this set of assembly directions and printed on the plastic pouch attached to crib spring.
Page 9
Φ Φ Φ Φ Φ BEFORE EACH USAGE OR ASSEMBLY, INSPECT CRIB FOR DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS OR SHARP EDGES. DO NOT USE CRIB IF ANY PARTS ARE MISSING OR BROKEN. ASK YOUR DEALER OR WRITE TO CHILD CRAFT, P.O. BOX 444, SALEM, IN 47167- 0444 USA (812)-883-3111)-service@childcraftind.com FOR REPLACEMENT PARTS AND IN- STRUCTIONAL LITERATURE IF NEEDED.
Need help?
Do you have a question about the Legacy Crib and is the answer not in the manual?
Questions and answers