Sealey PWTF2200 Manual

Sealey PWTF2200 Manual

Pressure washer twin flow150bar 810ltr/hr 230v

Advertisement

Thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. saFeTy
1.1.
eleCTriCal saFeTy
WarninG! It is the user's responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
Do noT pull or carry the appliance by the power cable.
8
Do noT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
Do noT use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Do noT connect either wire to the earth terminal.
8
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
General saFeTy
WarninG! Water and electricity are dangerous partners. Be extremely cautious and ALWAYS be aware that this device uses an
electric motor. Always plug into a RCD (See electrical safety above). Unplug from mains before changing accessories or servicing.
WarninG! Do noT use the washer if any part of the unit, gun, nozzle, detergent tank, hose or cables is damaged. Replace or
repair using genuine parts only. Unauthorised parts may be dangerous and will invalidate your warranty. Always check connections
are correctly secured and not cracked or damaged in any way before using the machine.
WarninG! Use washer on a flat, levelled surface, in an upright position. Failure to do so will invalidate your warranty.
neVer lay the washer down during use.
8
ensure you comply with all local water supply regulations. Power washers may only be connected to mains water supply if a check
9
valve is installed in the supply hose, or at the tap outlet.
The supply hose must be reinforced, and have an internal diameter of 1/2". The water supply must be at least equal to the cleaner
9
capacity. The water temperature must noT exceed 122°F (50°C). The water supply pressure must noT exceed 6 bar (90psi).
Always be aware of the hazards that may occur during use. Study all applications and limitations of the washer before use.
9
Use where air can freely circulate around the washer to avoid the machine overheating.
9
Keep the washer in good condition. Use an authorised service agent to service the unit. Only use authorised spare parts.
9
Wear adequate protective clothing, goggles and anti-slip rubber soled footwear.
9
Position the washer as near to the water supply as possible.
9
WarninG! Ensure all persons and animals keep at a minimum distance of 15mtr from the washer when in use. All persons within
15mtrs shall wear appropriate P.P.E.
WarninG! The pressure washer must only be used with clean water. Unfiltered water or corrosive chemicals must not be used as
these will damage the cleaner.
ensure the nozzle is aimed correctly at the work surface before switching on the machine.
9
Before activating the trigger, grip the gun firmly to counteract the recoil from the high pressure water jet.
9
© Jack Sealey limited
Pressure Washer TWin FloW150bar
810lTr/hr 230V
Model no:
Wear protective
Wear safety
gloves
footwear
Original Language Version
PWTF2200
Wear protective
Wear ear
clothing
protection
Do noT direct jet
Do noT
drink water
against yourself, other
from pressure
persons, animals,
washer
electrical equipment or
the machine itself
Recommended fuse rating
13 Amp
PWTF2200 Issue 1 20/12/18

Advertisement

Table of Contents
loading

Summary of Contents for Sealey PWTF2200

  • Page 1 PWTF2200 Model no: Thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2: Specification

    Twin flow lance included will boost cleaning performance on wide surfaces, saving a lot of your time and effort, up to 70%. Fitted with 8m high pressure hose, 5m power cable and heavy-duty wheels. 3. sPeCiFiCaTion Model no: ............PWTF2200 Hose length:..............8m IP Rating: ............... IPX5 Maximum Inlet Pressure: ..........10bar...
  • Page 3 Adjust Handles to correct height, by pressing the top button in the cable tidy hook (fig.2). 4.1.2 Unlock the spool handle (fig.2). 4.1.3 Slide the lance holder into place (fig.2). fig.1 fig.2 PWTF2200 Issue 1 20/12/18 Original Language Version © Jack Sealey limited...
  • Page 4: Electrical Connection

    “IPX5” protection level. The cross-section of the extension cable should be proportionate to its length; the longer it is, the greater its cross-section should be. 4.6.2. Plug in after assembly. Original Language Version PWTF2200 Issue 1 20/12/18 © Jack Sealey limited...
  • Page 5: Operation

    Always use the appliance at the lowest pressure setting when cleaning in the vicinity of wheels and tyres. 5.5.4. Never use the “Turbo Lance” for washing any part of the vehicle. 5.5.5. For further information refer to section: “Recommended cleaning procedure”. Original Language Version PWTF2200 Issue 1 20/12/18 © Jack Sealey limited...
  • Page 6: Recommended Cleaning Procedure

    6) Engage the gun safety catch (fig.6.D). 6.4. enD-oF-season sToraGe 6.4.1. Treat the appliance with non-corrosive, non-toxic antifreeze before storing it away for winter. Put the appliance in a dry place, protected from frost. Original Language Version PWTF2200 Issue 1 20/12/18 © Jack Sealey limited...
  • Page 7: Troubleshooting

    7. TroubleshooTinG Problem Possible causes Remedy nozzle worn Replace nozzle Water filter fouled Clean filter (L) (fig.9) Insufficient water supply Turn on water supply tap fully Air being sucked into system Check tightness of hose fittings Switch off the appliance and keep depressing and releasing the gun trigger until the water Air in pump Pump does not reach working pressure...
  • Page 8: Environment Protection

    Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. sealey Group, Kempson Way, suffolk business Park, bury st edmunds, suffolk. iP32 7ar 01284 757500 01284 703534 sales@sealey.co.uk...

Table of Contents