CP2-NA-LTE -Table of Contents Warning: Safety Alert: Introduction: Recording Playback & Analysis Package Contents: Hardware Overview: Front View Left Side View Driver-Facing View Top View Installation: First Steps Power Adapter and Wiring: Secondary Camera Connection: Troubleshooting: LED Status:...
All cellular-enabled CP2 devices must use the installation wizard for proper onboarding and activation, please visit install.smartwitness.com to register, login, and use the SmartInstall wizard. smartwitness.com | 1016 Lunt Ave. Schaumburg, Illinois U.S.A. | Tel: 312.981.8774 | sales.usa@smartwitness.com...
Warning TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. smartwitness.com | 1016 Lunt Ave. Schaumburg, Illinois U.S.A. | Tel: 312.981.8774 | sales.usa@smartwitness.com...
Actual Events, Driving Offence Allegations (speeding, traffic signal violations, swerving, etc.). When a SIM card is inserted, CP2-LTE is able to send video and driving data via a cellular network (T-Mobile or AT&T in USA, Bell or Rogers in Canada). North American customers can use the CP2- LTE to transmit safety critical video directly to a server (SmartWitness server software required), or integrate with Telematics Software (Please contact us for a list of compatible telematics software).
Driver-Facing View Communication Green LED Warning Panic Red LED Button G-Sensor Record Calibration Button Blue LED Top View Windsheild Mount Pivoting Bracket Locking Cover Camera Lens smartwitness.com | 1016 Lunt Ave. Schaumburg, Illinois U.S.A. | Tel: 312.981.8774 | sales.usa@smartwitness.com...
Installation First Steps Note: Step 1 and 2 is applicable only if customer did not order the SIM and SD from SmartWitness IMPORTANT: The unit’s power must be OFF to insert and/or remove SD snd SIM cards. Failure to turn the power off will result in damaging the cards.
Page 10
Please install in moderate temperature (recommended between 50°F ~ 80°F). 4. Peel the cover paper from the 3M adhesive on the CP2-LTE top. Mount the fully assembled unit to the windshield. Holding the camera in position with firm pressure for 30 seconds.
Connect the power cable before replacing the cover (see ”Power Adapter and Wiring”). Power Adapter and Wiring 1. To connect the CP2-LTE lead cable to the power adapter (INT1-T), lining up the arrows on the silver cable connectors and then push together. The power adapter switch can be turned to the “ON”...
Secondary Camera Connection A optional secondary camera can also be added to the CP2-LTE via Channel 2 input. The CP2-LTE is equipped with a simple plug & play connection. Simply connect the male end connector of the into the female end input on the CP2-LTE and mount the camera to the customer-specified location in the vehicle.
SmartWitness Support for instructions at support.smartwitness.com. 4. The CP2-LTE LED is solid • There may not be enough voltage/amperage. Check the power source or the ground connection may be bad. smartwitness.com | 1016 Lunt Ave. Schaumburg, Illinois U.S.A. | Tel: 312.981.8774 | sales.usa@smartwitness.com...
Data Network Slow On and connection error Slow On and communicate error Event Trigger G-Sensor, Panic Button, Alarm-In Beep No. 1 Over Speed Beep No. 4 (2 times) smartwitness.com | 1016 Lunt Ave. Schaumburg, Illinois U.S.A. | Tel: 312.981.8774 | sales.usa@smartwitness.com...
Page 15
T H I S I S V I D E O T E L E M AT I C S Notes smartwitness.com | 1016 Lunt Ave. Schaumburg, Illinois U.S.A. | Tel: 312.981.8774 | sales.usa@smartwitness.com...
Page 16
Our lineup of IOT dash cameras and accompanying REST API have allowed SmartWitness’ video and data to be seamlessly integrated with GPS tracking, telematics and fleet management software, ushering in the new era of Video Telematics. Our industry-leading safety...
Need help?
Do you have a question about the CP2-LTE and is the answer not in the manual?
Questions and answers