Table of Contents
Advertisement
NOTE: Before using the chart below, you should carefully read and understand the following statements.
These statements provide directions that apply to most floor types:
Always vacuum first.
•
Apply solutions to a
•
small area at a time,
approximately 3'x3'.
SOLUTIONS:
A - Aerus Wood Wax B - Aerus Floor Cleaner C - Aerus Cleaner Plus, Floor Cleaner & Stripper D - Aerus Tile Polish E - Aerus Turbo Shampoo
NOTE: A - D to be applied with a mist sprayer. E to be applied through dispenser tank.
SURFACE
FUNCTION
Stripping
VINYL, RUBBER,
ASPHALT, TERRAZZO,
STONE, MASONRY &
OTHER WAX FLOORS
Polishing
NO-WAX FLOORS
Cleaning
ORIGINAL
Wax Finish
WOOD FLOORS
(NON-LAMINATE)
OR CORK FLOORS*
Touch-Up
Plush or
CARPET
*Caution: Some finished wood floors are not suitable for wood floor wax
APPLICATION GUIDE
Clean accessories with
•
warm water when finished.
Scrubbing and polishing
•
requires scrub brushes.
TYPE/
SOLUTION
REQUIRED ACCESSORY(S)
•
•
C
•
•
•
D
•
•
•
•
B
•
•
A
•
•
•
Wax
A
•
•
•
E
Cut Pile
•
Berber,
Loop
E
•
or Shag
Clean out spray mister
•
before using.
Never use green pads on
•
easily marred surfaces.
Scrub Brushes
Green Scrub Pads
Mist Sprayer
Scrub Brushes
Green Scrub Pads
Lambswool Pads or
Disposable Polishing Pads
Mist Sprayer
Scrub Brushes
Lambswool or Disposable
Polishing Pads
Mist Sprayer
Scrub Brushes
Lambswool
Mist Sprayer
Scrub Brushes
Lambswool
Mist Sprayer
Shampoo Brushes
Nap Lifters
Shampoo Brush
Test carpeting for color
•
fastness and durability.
Always unplug unit before
•
changing brushes or pads.
APPLICATION
Spray a heavy, even mist of solution
•
Spread and work in using scrub brushes or scrub
•
pads (depending upon degree of soiling
and type of floor).
Mop up dirty solution, rinse and mop.
•
• Spray a moderate, even mist of solution
• Spread and work in using scrub brushes or scrub pads
(depending upon type of floor).
• Polish surface using scrub brushes.
• Once dry, buff using lambswool or disposable pads.
Spray a thin, even mist of solution
•
Spread and work in using scrub brushes
•
Once dry, buff using lambswool or
•
disposable pads
Spray a moderate to heavy mist of solution
•
Spread and work in using scrub brushes
•
Allow to dry
•
Polish surface using scrub brushes
•
Buff using lambswool or disposable pads
•
Spray a light mist of solution
•
Spread and work in using scrub brushes
•
Allow to dry
•
Buff using lambswool or disposable pads
•
Dispense foam and work into carpet
•
with shampoo brushes
Allow to dry
•
Naplift carpet then vacuum
•
Dispense foam and work into carpet
•
with shampoo brushes
Allow to dry
•
Vacuum (do not Naplift)
•
15
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the LUX FLOOR PRO and is the answer not in the manual?
Questions and answers
How do I set up for hardwood floors?
To set up the Aerus LUX FLOOR PRO for hardwood floors, follow these steps:
1. Prepare the Floor: Ensure the floor is clean by vacuuming it with an Aerus® Vacuum Cleaner to remove debris.
2. Position the Polisher: Place the polisher on the floor. Lock the handle in the upright position by pushing down the upper handle lock.
3. Attach Pads: If specific pads are required for hardwood floors (e.g., polishing pads), attach them to the polisher as per the manual's instructions.
4. Check Settings: Make sure the machine is properly configured for hardwood floor treatment, such as polishing or waxing, based on the manual's guidance.
5. Plug In: Once the handle is locked upright, plug in the cord.
6. Start Polishing: Use the polisher with the balanced triple-brush system to polish or wax the hardwood floor. Avoid solvents or gasoline near the machine.
This setup ensures effective cleaning and maintenance of hardwood floors.
This answer is automatically generated