Sealey IWMH1809R Instructions

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
indoor use
instruction only
manual
1. safety
1.1. electrical safety
warning! it is the user's responsibility to check the following:
‰
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and
all electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if the heater is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance
test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
do not pull or carry the appliance by the power cable.
8
do not pull the plug from the socket by the cable.
8
do not use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or
8
immediately by a qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. general safety
warning! Ensure the heater is at least 1m from any object, 30cm from the ceiling and 1.8m from floor level.
‰
familiarise yourself with the applications and limitations of the heater.
9
ensure the heater is in good order and condition before use. if in any doubt do not use the unit and contact your sealey dealer.
9
only use recommended attachments and parts. using unauthorised parts maybe dangerous and will invalidate your warranty.
9
Check that element guards are in place, undamaged and firmly attached.
9
Keep tools and other items away from the heater when it is in use.
9
Keep the work area clean and clear of unnecessary items.
9
Keep children and unauthorised persons away from the heater, as it gets very hot.
9
disconnect from mains and allow to cool before moving or attempting any cleaning or maintenance.
9
do not use this heater with timers or other devices which switch the heater on automatically.
8
do not get the heater wet or use in damp or wet locations or areas where there is condensation.
8
do not locate the heater below the power outlet.
8
do not move the heater whilst in operation or even when still warm.
8
do not locate the heater in an area where there are flammable gases, dust etc.
8
do not dismantle the heater for any reason. The heater must be checked by qualified personnel only.
8
do not use the heater to perform a task for which it has not been designed.
8
warning! if a fuse blows, ensure it is replaced with an identical fuse type and rating.
‰
When not in use, store the heater carefully in a safe, dry, childproof location.
9
warning! Never touch the element glass directly with fingers. Use a soft cloth, otherwise the tube may get damaged.
‰
warning! two dark points may exist on the surface of the heating element, or the surface of the heating element may turn white
‰
during the first few minutes of operation. This is normal and will not affect the performance of the heater.
warning! the warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
‰
may occur. it must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
© Jack sealey limited
instructions for
high efficiency carbon fibre infrared
wall heater 1800w/230V/with led lights
iwMh1809r/iwMh1809lr
model no's:
Original Language Version
replaced
recommended
fuse rating
13 Amp
iWMH1809R/LR | Issue:6 (L) 08/09/17