Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for CR Laser SUPER-3S
Summary of Contents for CR Laser SUPER-3S
- Page 1 Version: 1.0...
-
Page 2: Before Use
Laser Show System 1. FEATURES This device has been designed to produce decorative effect lighting and is used light show systems. High speed scanner. Super wide scanned angle. Several working modes: DMX controlled, 8channels Stand-alone with built-in microphone Stand-alone automatic mode DMX-addressing with LED display Preprogrammed multi-color laser shows Complies to EN/IEC 60825-1 for Laser Safety... -
Page 3: Safety Instructions
Laser Show System 3. SAFETY INSTRUCTIONS: Every person involved with installation and maintenance of this device have to: -be qualilfied -follow the instructions of this manual CAUTION! Be careful with your operations. Witch a high voltage you can suffer a dangerous electric shock when touching th wires! To protect the environment, please try to recycle the packing material as much as possible. -
Page 4: Laser Safety Instructions
Laser Show System Check that the available voltage is not higher than the one stated on the rear panel of the unit. The power cord should always be in perfect condition: switch the unit immediately off when the power cord is squashed or damaged. Never let the power-cord come into contact with other cables. -
Page 5: Overhead Rigging
Laser Show System This laser may only be used for shows. The operation of a class 3B show laser is only allowed if the operation is controlled by a skilled and well-trained operator. Depending on the classification, operating a laser product can produce laser radiation that may cause permanent eye damage and /or skin damage. -
Page 6: Connection To The Mains
Laser Show System Before rigging make sure that the installation area can hold a minimum point load of 10 times the device’s weight. Always use a certified safety cable that can hold 12 times the weight of the device when installing the unit. This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails. -
Page 7: Dmx-512 Connection/Connection Between Fixtures
Laser Show System 5.2 DMX-512 connection/connection between fixtures The fixture is equipped with 3-pin XLR sockets for DMX input and output. The sockets are wired in parallel. Only use a shielded twisted-pair cable designed for 3-pin XLR-plugs and connectors in order to connect the controller with the fixture or one fixture with another. - Page 8 Laser Show System 6. DESCRIPTION: 6.1 Back panel of the fixture NAME FUNCTION Mains input With socket and integrated fuse holder Switch Switch on and off the power Cooling fan Cooling and never cover this fan outlet Safety eye Attach the safety cable DMX output 3PINfemale XLR port，using for DMX DMX input...
- Page 9 Laser Show System NAME FUNCTION Y SIZE Adjust the Y axis X SIZE Adjust the X axis ILDA ILDA signal output， connecting another unit THOUGHT ILDA IN ILDA signal input Y MIRROR The picture on the Y direction X MIRROR The picture on the X direction 6.2 Front panel of the fixture...
- Page 10 Laser Show System NAME FUNCTION handing Fasten the machine bracket Power LED Indicate the unit is switch on DMX LED Indicate the unit is in the DMX mode Laser output Never seeing the laser direct 7. HOW TO SET UP AND CONTEROL THE UNIT Regular breaks during operation are essential to maximize the life of this device as it is not designed for continual use.
- Page 11 Laser Show System Put on some rhythmic music at the desired level. Turn the music sensitivity potentiometer until the laser beam nicely follows the beat of the music. 7.2 MULTI-UNIT WORK TOGETHER：(need connect by the cable) Set DIP of the MASTER laser switch number 10 OFF, and the1-9 is in any mode, and SLAVE lasers’...
- Page 12 Laser Show System 7.4 DMX OPERATED MODE: The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to “daisy chain” your DMX controller and all the connected light effects with a good quality XLR M/F balanced cable. Each effect in the chain needs to have its proper staring address so it knows which commands from the controller it has to decode.
-
Page 13: Dmx Protocol
Laser Show System 8. DMX PROTOCOL 8.1 DMX CHANNEL LIST: CHANNEL VALUE DESCRIPTION Switch off 000-51 052-103 Auto Running Line CH 1 104-155 Auto Running， 156-207 Sound Mode Line 208-255 Sound Mode CH 2 000-255 128 graphics 000-128 rotation( rotation by Z axis) CH 3 Adjust the speed of the rotation 129-255... - Page 14 Laser Show System CHANNEL VALUE DESCRIPTION Scanning speed CH 9 000-255 000-64 Original color 065-129 Yellow CH 10 130-194 195-255 Green...
-
Page 15: Maintenance
Laser Show System 9. MAINTENANCE Make sure the area below the installation place is free from unwanted persons during servicing Switch off the unit , unplug the mains cable and wait until the unit has been cooled down. During the inspection the following points should be checked: All screws used for installing the device and any of its parts should be tightly fastened and may not be corroded Housings, fixations and installations spots( ceiling, truss, suspensions) should... -
Page 16: Specifications
Laser Show System 10. SPECIFICATIONS Mains Input: AC110/230V, 50/60Hz Fuse: 250V 1.5A slow blow(20mm glass) Scanning Angle: 0~±20º Laser Diode Blanking: 1~1000Hz Sound Control: Internal microphone DMX connections: 3pin XLR male / female DMX channels: 10hannels Laser Power: Max. 60mW Green CW laser (λ=532nm) Max.
Need help?
Do you have a question about the SUPER-3S and is the answer not in the manual?
Questions and answers