Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for TREND T5
Summary of Contents for TREND T5
- Page 1 &...
-
Page 2: Table Of Contents
Dear Customer TECHNICAL DATA Thank you for purchasing this Trend product, we hope you enjoy many years of creative and Voltage: UK & Eire 240V productive use. UK & Eire only 115V Please remember to return your guarantee card Europe 230V within 28 days of purchase. -
Page 3: Safety
SAFETY covering to contain long hair. it on or off. Have defective switches replaced by an Authorised Service 5. Consider working environment. Do WARNING: Agent. not use the product in the rain or in a damp environment. Keep work area 17. - Page 4 Trend Routing Catalogue or on our contact with collet and nut. Ensure Using Routers In A Fixed Position website.
-
Page 5: Electrical Safety
Using an Extension Cable operated from a 220 volt supply. ■ If an extension cable is required, use an The T5 is double insulated in accordance with EN 50144; therefore no approved triple core extension cable suitable earth wire is required. -
Page 6: Manufacturers Declaration
INFORMATION ON NOISE/VIBRATION The noise level when working can exceed 85 dB(A). Wear ear protection! Weighted root mean square acceleration value according to EN 60745: < 2.5 m/s (hand arm method) Managing Director Stephen Phillips Trend Machinery & Cutting Tools Ltd. -
Page 7: Description Of Parts
DESCRIPTION OF PARTS A Plunge locking grip knob B Depth of cut scale C Depth stop D Motor housing E Power cable F On/Off switch: MK1 G Fixed Grip knob H Spindle lock Collet nut Dust spout 35mm dia. K Thumb knob with anti-vibration spring to secure fence rods L Router base M Template guide bush dia. -
Page 8: Assembly & Adjustment
ASSEMBLY & ADJUSTMENT Fitting and Removing the Dust Extractor Spout 35mm ■ Insert the extractor spout in channel ‘A’ of the routing base. The extractor spout is suitable for dust extractors with a hose diameter of 35mm. Fitting Dust ■ Press the extractor spout down and forward Extractor until it latches into channel ‘B’. -
Page 9: Switching On & Off
■ A slide switch above the fixed grip knob is without a No-Volt Release Switch. used to turn the router on and off. ■ The T5 has a soft start feature when switched Adjusting the Depth of Cut on and will take 1–2 seconds to reach full ■... -
Page 10: Fitting & Removing Cutters
How to Fit and Remove a Router Cutter Fitting Cutters ■ Insert at least of the shank length of the cutter (1) into the collet. ■ Press the spindle lock (2) forward until the router spindle is locked (you may need to turn the spindle slightly to engage it). -
Page 11: Speed Control
15mm Fixing Points for Accessories The router has two threaded holes M6 in its base that allow fitting of accessories and also fitting to router tables. A whole range of accessories are shown in the Trend Routing Catalogue. -10-... -
Page 12: Operation
OPERATION Cutting Direction Sequence of plunging The direction of routing must always be opposite to the cutter’s direction of rotation. Otherwise there is a risk of Step One kick-back. Plunge down and lock the motor carriage, with the plunge locking grip knob. Feed direction of router Step Two... -
Page 13: Side-Fence Routing
Side-Fence Routing The side-fence is used to guide the router when moulding, edge profiling or rebating the edge of the workpiece or when routing grooves and slots in the centre of the workpiece, parallel to the edge. The edge of the workpiece must be straight and true. -
Page 14: Template Guide Bush Routing
Using the Guide Bush The 20mm guide bush (1) is fastened to the router’s base from beneath using the two M5 countersunk machine screws (2) supplied. Routing with a Template The guide bush is used in conjunction with a template when the routing operation is repetitive or the workpiece is complex in shape. -
Page 15: Beam Trammel Routing
Beam Trammel Routing Cutting Arcs with the Router ■ Place the machine on the workpiece. ■ Set the cutting depth using the depth stop (2). ■ Fasten the fence rod (1) in the routing base (3) with the thumb knob (4). ■... -
Page 16: Bearing Guided Cutters
Bearing Guided Cutters Ball Bearing Guided Cutters Edge profiling and shaping cutters are available with a bearing fitted to the end. This enables shaped or straight workpieces to be routed without the need for a guiding device such as a side-fence or batten. -
Page 17: Freehand Routing & Batten Routing
Freehand Routing with the Router The T5 can also be used for signwriting or creative freehand work without any form of guide. With practice, numbers or name plate designs can be routed freehand. Draw the design or motif on the workpiece and then rout the design, taking shallow passes. -
Page 18: Maintenance & Care
Please call Trend Technical Support for advice as to how to dispose of unwanted Trend electrical product in an environmentally safe way. It is advisable to have the... -
Page 19: Spare Parts List
Deflector WP-T5/030 Armature 240V with Fan T5 & T5/EURO WP-T5E/031 Armature 115V with Fan T5EL WP-T5EL/031 Carbon & Holder 240V T5 & T5/EURO (2 sets) WP-T5E/032 Carbon & Holder 115V T5EL (2 sets) WP-T5EL/032 Brush Clamp WP-T5/033 Guide Rods 8mm x 300mm (pair) - Page 20 WP-T5/050 Machine Screw Cheese M5 x 10mm Slot WP-SCW/50 Washer 5.3mm x 10mm x 1mm WP-T5/052 Scale WP-T5/053 Speed Control Circuit Board 240V T5 & T5/EURO WP-T5E/055 Speed Control Circuit Board 115V T5EL WP-T5EL/055 Speed Control Dial WP-T5E/056 Insertion Socket...
-
Page 21: Spare Parts Diagram
T5 MK1 - SPARE PARTS DIAGRAM v8.0 09/2005 T5 MK2 - SWITCH -20-... - Page 22 Web: ____________www.trendmachinery.co.uk RECYCLABLE © Copyright Trend 2005. No part of this publication may be reproduced, stored or transmitted in any form without prior permission. Our policy of continuous improvement means that specifications may change without notice. Trend Machinery and Cutting Tools...
Need help?
Do you have a question about the T5 and is the answer not in the manual?
Questions and answers