Dormakaba ED 100 Mounting Instructions
  1. Manuals
  2. Brands
  3. Dormakaba Manuals
  4. Door Opening System
  5. ED100
  6. Mounting instructions

Dormakaba ED 100 Mounting Instructions

Hide thumbs Also See for ED 100:
Table of Contents

Advertisement

Quick Links

Download this manual
ED 100, ED 250
Mounting instructions
WN 059799 45532/14005 – 2019-07
EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ED 100 and is the answer not in the manual?

Questions and answers

Related Manuals for Dormakaba ED 100

Summary of Contents for Dormakaba ED 100

  • Page 1 ED 100, ED 250 Mounting instructions WN 059799 45532/14005 – 2019-07...

  • Page 2: Table Of Contents

    Limitation of liability This danger spot cannot be influenced by the drive ED 100 and ED 250 must only be used according to manufacturer. Its safeguard is often not feasible from their intended use.

  • Page 3: Safety

    WARNING Danger to life through electric current This signal word indicates a possible If the ED 100 or ED 250 is mounted on a hazardous situation which may result in metal door leaf, there is a risk of the current death or serious injury if ignored.

  • Page 4: Product Description

    Operating modes 23 N (5 lbf) unless the hold-open system has been The ED 100, ED 250 can be operated in 2 modes: as activated or the power failed. This power-assist a door closer or an automatic swing door drive. In...
  • Page 5 < 3s LEARN Low energy product > 8s The ED 100/250 can be adjusted so that the Fact-Setup requirements of a low energy application (low energy drive unit) are in accordance with the EN 16005 or DIN 18650, ANSI 156.19 and BS 7036-4. During...
  • Page 6 ED 100 and ED 250. During the installation of the hold-open time and impulse relay. It can be used for Upgrade Cards, information between the control unit 2-panel systems.
  • Page 7 Outputs Connecting terminals max. 1,5 mm Factory setting: Out 1 4 Out 2 2 Out 3 5 Out 4 6 Door closed Potential-free status Door open contact Error Door closed and locked ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 8 Door opening in only be reached in operatiang mode full-energy, a Push & Go function case of a manual low door leaf weight and a learned opening angle movement of 4° of min. 95°. ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 9 If power-assist support set to maximum, effective from an opening width of approx. 3°. The torque is available in the event of automatic opening in automatic mode. In the push version of the slide channel installation type, the forces reduce by approx. 33%. ED 100, ED 250 WN 059799 45532 2019-07...

  • Page 10: Preparing For Installation

    Combination not possible 2. Depending on the installation situation, select the corresponding drilling pattern on pages 11 – 18. 3. Drill the holes shown in the drilling pattern in the door leaf and frame/wall. ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 11 ● 61 mm 80 mm 52 mm 71 mm 60 mm ● ● 91 mm 110 mm 82 mm 101 mm 90 mm ● 121 mm 140 mm 112 mm 131 mm ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 12 ● 61 mm 93 mm 52 mm 84 mm 60 mm ● ● 91 mm 123 mm 82 mm 114 mm 90 mm ● 121 mm 153 mm 112 mm 144 mm ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 13 ● 61 mm 92 mm 52 mm 83 mm 60 mm ● ● 91 mm 122 mm 82 mm 113 mm 90 mm ● 121 mm 152 mm 112 mm 143 mm ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 14 ● 61 mm 105 mm 52 mm 96 mm 60 mm ● ● 91 mm 135 mm 82 mm 126 mm 90 mm ● 121 mm 165 mm 112 mm 156 mm ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 15 ● 44 mm 79 mm 35 mm 70 mm 60 mm ● ● 74 mm 109 mm 65 mm 100 mm 90 mm ● 104 mm 139 mm 95 mm 130 mm ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 16 Assembly on the opposite hinge side push version with arm assembly Ø 6,6 Lower edge frame Space for cable feed Lower edge frame ED 100 = 0 mm – 300 mm ED 250 = 0 mm – 500 mm Axis extension ED 100 ED 250 Standard ●...
  • Page 17 Assembly on the opposite hinge side push version with arm assembly EN 7 Ø 6,6 Lower edge frame Note lever position! Space for cable feed Lower edge frame ED 100 = 0 mm – 300 mm ED 250 = 0 mm – 500 mm Axis extension ED 100 ED 250 Standard ●...
  • Page 18 ● 45 mm 91 mm 36 mm 82 mm 60 mm ● ● 75 mm 121 mm 66 mm 112 mm 90 mm ● 105 mm 151 mm 96 mm 142 mm ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 19 ● 61 mm 91 mm 52 mm 82 mm 60 mm ● ● 91 mm 121 mm 82 mm 112 mm 90 mm ● 121 mm 151 mm 112 mm 142 mm ED 100, ED 250 WN 059799 45532 2019-07...

  • Page 20: Installing The Drive Unit

    Use a screwdriver as a lever between the drive unit and the base plate. 4. Place a piece of wood or similar underneath the drive unit so that the connecting part cannot come loose. ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 21 5.5.3 Mounting the receiver (optional) Screw the receiver board to the drive unit. 2. Feed the cable through the holder. 3. Connect the receiver. + 24 V Impuls wh ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 22 2. Push the drive unit until it clicks audibly into place. 3. Tighten the 8 screws. 4. Plug in the mains connector. ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 23 Mounting part 3. Screw the slide channel with 2 screws into the prepared holes. For the fastening, use dowels and screws that match the background. 4. Insert the casing onto the slide channel. ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 24 Put the lever on the axle. 8. Screw the lever on tight with 23 Nm. 23 Nm Screw the lever bolt into the lever. 10. Screw the lever bolt tight with 8 – 10 Nm. 8 – 10 Nm ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 25 Push the telescopic arm’s ball head into the holder on the lever. 8. Turn the rod so that the telescopic arm is at an angle of 90° to the door leaf. Tighten the 2 screws. 90° ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 26 The speed must be adjusted. If the door closes in less than 3 seconds, it will lead to the error message 73 (braking circuit test). 5.17 Commissioning the drive unit. Commission the drive unit. Cf. commissioning on page 33. ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 27 2. Move the buffer and the end stop to 5 mm to the sliding piece. 3. Tighten the end stop. ATTENTION! dormakaba recommends the use of a doorstop. When using the standard rod, a doorstop must be used. 5.19 Installing the casing ATTENTION! Do not pinch any wires.
  • Page 28 There are 3 options to connect the mounting plates. The clearance determines which option is used. Clearance 1,400 – 1,415 mm = connection “A“ Clearance 1,416 – 1,475 mm = connection “B“ Clearance larger 1,476 mm = connection “C“ ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 29 In case the system is to be fitted with an electrical door coordinator, install it now (see installation manual ED 100/250 ESR). In case the system shall be equipped with an integrated smoke detector, install the integrated smoke detector now cf.
  • Page 30 22. Connect the mains connection cable for the second drive unit. Figure shows the connection on the active panel. Figure shows the connection on the inactive panel. ED 100, ED 250 WN 059799 45532 2019-07...

  • Page 31: Connecting The Accessories

    1 15 17 3 1 11 13 3 maximum 1 A load on terminal 1G. Connection depends on the + 24 V smoke detector Locking relay max. 1 A/48 V DC/AC Locking response ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 32 • On the outside: a status display „free/occupied“ • On the inside: a status display „occupied“. Emergency buttons can be installed optionally on the inside and outside. dormakaba recommends to include the barrier-free WC into an emergency call system provided by the customer.

  • Page 33: Commissioning

    The device identification will “run“ through The door is now operational. the display. ED 100 or ED 250 and the firmware version (indicated by XX XX). A small, spinning “o“ and “P“ indicate that a further parameterization is required (only...

  • Page 34: Installing Upgrade Cards

    LED. ‣ The corresponding function is now enabled and can be activated (see page 39, Parameter F1 – F8). ‣ The system is now operational. ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 35 Install the Upgrade Card Barrier-free WC as described in 8.3 and 8.4. 4. Attach the container module. 2. Switch off and on again the ED 100, ED 250 ‣ The control unit so that the functions are applied. When using...

  • Page 36: Parameterization

    OHC_L Lintel assembly opposite hinge side, arms push version EN7 Lintel depth ED 100: – 3 – 30 The lintel depth is set in 10 mm steps. The required measure can be ED 250: – 3 – 50 taken from the assembly drawings.
  • Page 37 Due to system tolerances, the actual forces on the control) door panel have to be measured after the automatic drive teach- in run and adjusted, if necessary, in order to comply with the local standards and regulations. ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 38 This results in a faster opening in combination with motor locks. When an e-opener is used, this opener must be suitable for a 100 % switch-on time in order to prevent damage. ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 39 Power-assist 1 – 5 Degree Sets the angle after which the power-assist function is to be starting angle effective. The smaller the value, the more sensitive the response of the power-assist function. ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 40 10 seconds. With the use of the Upgrade Card Barrier-free WC, the inputs and outputs of the control unit are assigned with the functions specially required for this application. The required accessory components can be directly connected. ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 41 0 = not active Special function 0 – 1 OHC-modified obstacle detection 1 = active Special function 0 – 1 0 = not active Reversing at triggering SL-BGS in mode hd=1 1 = active ED 100, ED 250 WN 059799 45532 2019-07...

  • Page 42: 10 Diagnosis/Troubleshooting

    10 Diagnosis/troubleshooting 10.1 Information “In“ Information is provided for the easy servicing of dormakaba drive units ED 100, ED 250 meet a the drive unit and points to both faulty states and high safety standard and comply with all technical operating states that suppress the automatic regulations and requirements.
  • Page 43 Repeat the teach-in run with the motor cold. from the set parameters. with a warm motor and the door panel weight was therefore incorrectly determined. LED red LED yellow Mains switch LED green ED 100, ED 250 WN 059799 45532 2019-07...

  • Page 44: Error Messages

    The information is shown in this case This, for example, is the case if the door is manually passed through during the measurement. The test will be automatically repeated. ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 45 The test can be noticed as a closing speed, the control unit must be replaced. short jerk on the door panel and is no reason for a complaint. Short circuit of the 24V supply voltage Eliminate short circuit. ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 46 The movement dynamics in the OPEN and CLOSED The system responds automatically. direction will be reduced. The system shuts down for 3 minutes (door closer mode). The hold-open time will be extended. ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 47 Mounting instructions ED 100, ED 250 WN 059799 45532 2019-07...
  • Page 48 Deutschland GmbH DORMA Platz 1 58256 Ennepetal Deutschland T: +49 2333 793-0 www.dormakaba.com F: +49 2333 793-4950...

This manual is also suitable for:

Ed 250

Table of Contents