Related Manuals for Flymo EasiLife 200
Summary of Contents for Flymo EasiLife 200
- Page 1 Robotic Lawn mower EasiLife 200 EasiLife 350 EasiLife 500 Operator‘s manual Easier by Design www.flymo.com/uk FRONTCOVER_P01_Flymo.indd 1 FRONTCOVER_P01_Flymo.indd 1 2019-11-18 14:54:44 2019-11-18 14:54:44...
-
Page 2: Table Of Contents
Contents 5.5 Winter service...........37 1 Introduction 6 Troubleshooting 1.1 Introduction..........3 1.2 Product overview........4 6.1 Introduction - troubleshooting....39 1.3 Symbols on the product......5 6.2 Fault messages........39 1.4 Symbols on the display......5 6.3 Information messages......44 1.5 Symbols on the battery.......5 6.4 Indicator lamp in the charging station..45 1.6 General manual instructions.......6 6.5 Symptoms.......... -
Page 3: Introduction
Product registration key: The serial number is on the product rating plate and on the product carton. • Use the serial number to register your product on www.flymo.com/uk. 1.1.1 Support The operator selects the operation settings with For support about the Flymo product, speak to the keys on the keypad. -
Page 4: Product Overview
1.2 Product overview The numbers in the figure represent: 11. Display 12. ON/OFF button Body 13. Keypad Hatch to display, height adjustment and 14. Cutting system keypad 15. Blade disc Stop button 16. Handle Rear wheel 17. Chassis box with electronics, battery and Front wheels motors Charging station... -
Page 5: Symbols On The Product
23. Connector for the loop wire The low voltage cable must not be 24. Screws for securing the charging station shortened, extended or spliced. 25. Measurement gauge for help when installing Do not use a trimmer nearby the low the boundary wire (broken loose from the voltage cable. -
Page 6: General Manual Instructions
italics is a text that is shown • Text written in Do not discard the battery into fire and on the display of the product or is a do not expose the battery to a heat reference to another section in the source. -
Page 7: Menu Structure Overview 1
1.7 Menu structure overview 1 Schedule Wizard Advanced Overview week Period 1 Period 2 Copy Reset Current All week days LawnSense Cutting time LawnSense Low/Mid/High 1392 - 001 - Introduction - 7... -
Page 8: Menu Structure Overview 2
1.8 Menu structure overview 2 Settings Security Lawn coverage Installation General Mower FrostSense Bluetooth Starting Drive house point mode past wire Remove Area 1-3 paired pairing device Security level Advanced New loop Change Time & Language Unit Reset all About Country signal PIN code... -
Page 9: Display
1.9 Display The display on the product shows information and settings of the product. To access the display, push the STOP button and open the hatch. 1.10 Keypad Use the keypad on the product to navigate in the menu. To access the keypad, push the STOP button and open the hatch. -
Page 10: Safety
2 Safety 2.1 IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE The operator is responsible for accidents or hazards occurring to other people or property. This appliance is not intended for use by persons (including chil- dren) with reduced physical, sensory or mental capabilities (that could affect a safe handling of the product), or lack of experience and knowledge, unless they have been given supervision or in- struction concerning use of the appliance by a person responsible... -
Page 11: Safety Definitions
2.3 Safety instructions for operation WARNING: The product can be dangerous if used 2.3.1 Use • The product may only be used with the incorrectly. equipment recommended by the manufacturer. All other types of use are incorrect. The manufacturer’s instructions with regard to operation/maintenance must WARNING: Do not use be followed precisely. - Page 12 The product can only start when the ON/OFF button has been switched on and the correct PIN code has been entered. • FLYMO does not guarantee full compatibility between the product and other types of 12 - Safety 1392 - 001 -...
- Page 13 cleaning or maintenance of the charging station or the loop wire. Push the ON/OFF button for 3 seconds and make sure the product is switched off. Check that the indicator lamp on the keypad is not lit. This means that the product is Indicator lamp in the disabled.
-
Page 14: Installation
• Make a mark on the blueprint where to put the charging station, the boundary wire and the guide wire. Note: Refer to www.flymo.com/uk for more • Make a mark on the blueprint where the information about installation. guide wire connects to the boundary wire. - Page 15 60- cm / 24- in. 3.4.2 To examine where to put the power supply • Put the charging station near a power outlet. • Put the charging station on a level surface. WARNING: Do not cut or extend the low-voltage cable. There is a risk of electrical shock.
- Page 16 3.4.3 To examine where to put the boundary wire CAUTION: If the work area is adjacent to water bodies, slopes, precipices or a public road, the boundary wire must have a protective wall. The wall must be minimum 15 cm / 6 in. in height. CAUTION: Do not let the product operate on gravel.
- Page 17 >10% 0-25% " 10 cm / 4 " max 1 cm / 0.4 • For slopes adjacent to a public road, put a • If you have a paving stone path that is in fence or a protective wall along the outer level with the lawn, put the boundary wire edge of the slope.
- Page 18 CAUTION: Do not put the guide wire across the boundary wire, for example a boundary wire that goes to an island. 0 cm / 0" 3.4.3.4 To make a secondary area Make a secondary area (B) if the work area has 2 areas that are not connected with a passage.
-
Page 19: Installation Of The Product
3.4.4 To examine where to put the guide boundary wire is at a minimum 2 m / 6.6 ft. in front of the charging station. wire • If the work area has a passage (B), make Put the guide wire from the charging station sure that the distance to the boundary wire through the work area and connect it to the is at a minimum 2 m / 6.5 ft. - Page 20 WARNING: The product is only to be Connect the low-voltage cable to the used with the power supply unit charging station. supplied by Flymo. Put the power supply at a minimum height of 30 cm / 12 in. WARNING: Do not put the power supply at a height where there is a risk it can be put in water.
- Page 21 3.5.3 To install the boundary wire Push the connector onto the metal pin on the charging station with the mark "G". CAUTION: Do not put unwanted wire Disconnect the charging station from the in a coil. The coil causes interference power outlet.
-
Page 22: To Put The Wire Into Position With Stakes
11. Connect the charging station to the power Put the boundary wire or the guide wire into outlet. position. Put the wire ends into a coupler. 3.6 To put the wire into position with Note: Make sure that you can see the ends stakes of the boundary wire or the guide wire through the transparent area of the coupler. -
Page 23: To Do The Product Settings
3.9.2 To do the basic settings Use the arrow buttons and the OK button to move through the menu structure Advanced Before the product starts to operate for the first > Calibrate > Guide calibration . time, you must do the basic settings. Place the product in the charging station. - Page 24 / 5400 ft , cut with a Schedule move through the menu structure Flymo EasiLife specified for 500 m > Advanced > Overview . 500 m / 41 ≈ 8.5 h. Use the arrow buttons and the OK button to select the day.
- Page 25 LawnSense selects 3.10.3.4 To copy the schedule setting 1 mowing cycle, and then the if the product will continue to operate or not. Do steps 1–3 in To get access to the menu on page 23 . LawnSense is reset if the product does Note: The Use the arrow buttons and the OK button to Reset...
- Page 26 Enter the new PIN code. Function High Push the OK button. PIN-code Enter the new PIN code. Time lock Push the OK button. Make a note of the new PIN code. Refer to • PIN-code - The correct PIN-code must be Introduction on page 3 .
- Page 27 Put the product in the charging station. Note: To prevent that the grass in the narrow To get access to the menu Do steps 1–3 in passage is worn, Flymo recommends to set a low on page 23 . PassageSense . percentage for the Use the arrow buttons and the OK button to Settings >...
- Page 28 Push the STOP button when the product is at the distance you select to measure. The distance shows in the display. 3.10.7.5 To disable or enable the Lawn Coverage function Lawn Coverage function for Disable or enable the each area. To get access to the menu Do steps 1–3 in on page 23 .
- Page 29 3.10.13 Bluetooth The product can connect to mobile devices that 3.10.10.1 To set the ECO mode have the Flymo app installed. Flymo is a free app To get access to the menu Do steps 1–3 in for your mobile device. The short-range on page 23 .
- Page 30 Use the arrow buttons to set the date format and then push the BACK button. 3.10.14.2 To set the language To get access to the menu Do steps 1–3 in on page 23 . Use the arrow buttons and the OK button to move through the menu structure Settings >...
-
Page 31: Operation
4 Operation 4.1 The ON/OFF button must push the ON/OFF button for 3 seconds to make the product active again. WARNING: Read the safety • The product is disabled when the indicator instructions carefully before you start lamp is not lit. the product. -
Page 32: To Stop The Product
Override schedule • 4.3.5 Override schedule • Spot cutting The schedule settings can be temporarily Override schedule . It is overridden by selecting possible to override the schedule for 3 h. It is not possible to override a standby period. 4.3.6 Spot cutting Spot cutting function is activated with the GO button and is useful for quickly mowing an area... -
Page 33: Schedule And Standby
Check that the indicator lamp on the keypad is not lit. 4.6 Schedule and Standby The product has an inbuilt standby period according to the Standby time table. The standby period provides for instance a good opportunity to water or play games on the lawn. The standby time is depending on how much active time (cutting and searching) the product has each day. -
Page 34: To Charge The Battery
4.8 Adjust the cutting height CAUTION: During the first weeks after a new installation, the cutting height must be set to MAX to avoid damaging the loop wire. After this, the cutting height can be lowered step by step every week until the desired cutting height has been reached. -
Page 35: Maintenance
Flymo offers a special cleaning and maintenance done. The product is disabled when kit as an accessory. Contact your Flymo central the indicator lamp on the keypad is not service. lit. -
Page 36: Replace The Blades
All 3 blades and screws must be replaced at the same time to obtain a balanced cutting system. Use Flymo original blades embossed with the crowned H- Warranty on page 53 . -
Page 37: Winter Service
5.5 Winter service Clean around the battery cover. Take your product to your Flymo central service Unscrew the screws to the battery cover for service prior to winter storage. Regular winter (Torx 20) and remove the battery cover. - Page 38 • Thorough cleaning of the body, the chassis, the blade disc and all other moving parts. • Testing of the product’s function and components. • Checking and, if required, replacing wear items such as blades and bearings. • Testing the product’s battery capacity as well as a recommendation to replace battery if necessary.
-
Page 39: Troubleshooting
6.2 Fault messages The fault messages in the table below are shown in the display of the product. Speak to your Flymo customer service if the same message shows frequently. - Page 40 Wrong PIN code Wrong PIN code has been entered. Enter the correct PIN code. Contact Five attempts are permitted, and the Flymo customer service if you forget keypad is then blocked for five minutes. the PIN code. No drive The product has got caught in some- Free the product and rectify the reason thing.
- Page 41 Message Cause Action Charging station The contact between the charging Put the product in the charging station blocked plates (product) and contact plates and check that the charging plates and (charging station) may be poor and the contact plates make good contact. product has made a number of at- tempts to charge.
- Page 42 Message Cause Action Safety function Temporary electronic or firmware rela- Restart the product. faulty ted issue in the product. If the problem remains, the message requires action by authorized service Electronic problem technician. Loop sensor prob- lem, front/rear Charging system problem Tilt sensor prob- Temporary prob-...
- Page 43 Message Cause Action No loop signal The power supply is not connected. Check the wall socket connection and whether an earth-fault breaker has trip- ped or not. Check that the low voltage cable is connected to the charging sta- tion. The low voltage cable is damaged or Check that the low voltage cable is not not connected.
-
Page 44: Information Messages
6.3 Information messages The information messages in the table below are shown in the display of the product. Speak to your Flymo customer service if the same message shows frequently. Message Cause Action Low battery The product cannot find the charging Check that the charging station and the station. -
Page 45: Indicator Lamp In The Charging Station
The indicator lamp in the charging station must show a solid or flashing green light for a correct installation. If not, follow the instructions in the troubleshooting guide below. You can also find information on www.flymo.com/uk. Speak to your Flymo customer service for more information. -
Page 46: Symptoms
If your product does not work as expected, follow the symptoms guide below. There is a FAQ (Frequently Asked Questions) on www.flymo.com/uk which provides more detailed answers to a number of standard questions. Contact Flymo customer service if you still cannot find the reason for the fault. -
Page 47: Find Breaks In The Loop Wire
Symptoms Cause Action Battery Both the mowing The battery is spent. Replace the battery. Refer to on page 36 . and charging times are shorter than usual. The product is The product has an inbuilt standby peri- No action. parked for hours in od according to the Standby time table. - Page 48 always select the maximum cutting height the first weeks after installation and then lower the GUIDE height one step at a time every second week until the desired cutting height has been reached. A defective splicing of the loop wire can also lead to disruptions several weeks after the splice was POWER done.
- Page 49 b) If the suspected boundary wire is long (thick black line) then do as follows: Put L and GUIDE back to their original positions. Then disconnect R. Connect a new loop wire to R. Connect the other end of this new loop wire at the middle of the suspected wire section.
-
Page 50: Transportation, Storage And Disposal
Note: If you keep the charging station outdoors, do not disconnect the power supply and the connectors. • Contact Flymo sales representative about what accessories are available for your product. 7.3 Disposal • Obey the local recycling requirements and applicable regulations. -
Page 51: Technical Data
8 Technical data 8.1 Technical data Data Flymo EasiLife Dimensions Length, cm / in. 55 / 21.7 Width, cm / in. 38 / 15.0 Height, cm / in. 23 / 9.1 Weight, kg / lb 7.3 / 16 Electrical system Flymo EasiLife Battery, Lithium-Ion 18 V/2.0 Ah Art.No... - Page 52 Noise emissions measured in the environment as sound power Flymo EasiLife Measured sound power noise level, dB (A) Guaranteed sound power noise level, dB (A) Sound pressure noise level at the operator’s ear, dB (A) The noise emission declarations conforms to EN 50636-2-107:2015...
-
Page 53: Warranty
The blades and wheels are seen as disposable and are not covered by the warranty. If an error occurs with your Flymo product, please contact Flymo customer service for further instructions. Please have the receipt and the product’s serial number at hand when contacting Flymo customer service. -
Page 54: Ec Declaration Of Conformity
Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares that the robotic (Authorized representative for Husqvarna AB and lawn mowers Flymo EasiLife with serial numbers responsible for technical documentation.) dating 2019 week 47 and onwards (the year and week is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE:... - Page 55 1392 - 001 - EC Declaration of Conformity - 55...
- Page 56 © Copyright 2019 Flymo S.A. All rights reserved Flymo and other product and feature names are registered trademarks of Flymo S.A. The Husqvarna UK policy of continuous improvement and updating means that specifi cations can be altered without prior notice. All measurements quoted are approximate.
Need help?
Do you have a question about the EasiLife 200 and is the answer not in the manual?
Questions and answers