Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CNB MPC1070PN
Summary of Contents for CNB MPC1070PN
- Page 1 MPC1070PN 5M Pixel Panoramic IP Camera...
- Page 2 CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
- Page 3 Regulatory Notice This equipment has been tested and found to comply with limits for a class of digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
-
Page 4: Table Of Contents
Contents Introduction ..............................5 1.1. Overview ..............................5 1.2. Features & Specification ........................... 6 1.2.1. s ............................6 n ..........................6 1.3. Applications of IP Camera ........................9 Product Description ............................ 10 2.1. Contents ..............................10 2.2. Product Preview............................10 2.3. -
Page 5: Introduction
PC or smart device. Real time 2-way communication is available through bidirectional audio communication feature. Designed to be a stand-alone streaming audio & video transmission device, MPC1070PN can be applied to various application area such as video security, remote video monitoring, distance education, video conference or internet broadcasting system. -
Page 6: Features & Specification
1.2. Features & Specification 1.2.1. • Max. 5MP(2592x1944) up to 10FPS • Focal Length: 0.98mm (Short axis) 1.12mm (Long axis) • Built-in Panomorph Lens (Immervision360˚) • 1/2.5” Progressive CMOS Sensor • Super Wide Angle of 182˚x 360˚FOV • View Modes : Single PTZ View, 4 PTZ View in 1 Window, Perimeter View in One Window(2x180˚) •... - Page 7 IPv4/6, TCP/IP, UDP, IGMP, ICMP, ARP, RARP, PPPoE, RTCP, RTP, RTSP, SDP, HTTP, Protocol HTTPS, SMTP, FTP, DHCP, UPnPP, NTP, DNS, DynDNS, Socks Supported DDNS Supported (CNB DDNS) User ID & Password protection, IP address filtering, HTTPS encryption, Digest Authentication, Security User Access Log...
- Page 8 Approx. 400g Weight Rev.1.4...
-
Page 9: Applications Of Ip Camera
1.3. Applications of IP Camera Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities, military, etc.) Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.) eleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting Weather and environmental observation Rev.1.4... -
Page 10: Product Description
2.1. Contents The product package contains followings : Contents Description Remarks IP Camera IP camera MPC1070PN main unit CVBS Cable 1EA, Screws (4 pieces of 1 type), Accessories Anchors (4 pieces of 1 type), L-type wrench with six angles 1EA Software &... -
Page 11: Physical Description
2.3. Physical description 2.3.1. External View Figure 2-1. External view of IP Camera 2.3.2. Dimension Unit : mm Figure 2-2. Dimension Rev.1.4... -
Page 12: External Connector
2.3.3. External Connector Sensor Input (white(+), Red(-)) Relay Output (Black(+), Yellow(-)) Line Output Network (LAN) Power Mic/Line Input Figure 2-3. Connector for external connection 2.3.4. Factory Default Switch Factory default switch is provided for returning the IP camera to factory default state. Unscrew the cover to access the switch. -
Page 13: Functional Description
2.4. Functional Description Power : Power input for supplying 12V DC power. Caution : If IP Camera is powered by PoE, do not plug in DC Jack with active DC power into DC power connector. Network (LAN) 100Mbps Ethernet connector (RJ-45) with PoE standard (802.3af). ... - Page 14 Relay Output Relay output is provided for connecting alarm devices or for remote on/off control of devices such as light. Relay is normal open and it will be closed upon alarm annunciation or remote on. The relay is capable of switching 30V AC/DC, 2A.
-
Page 15: On Site Installation
3. On Site Installation Use cables and conduits that are suitable for the installation. Particular attention should be paid in the installation so that no moisture is allowed to penetrate into the unit through the cables or conduits during the life time of the product. - Page 16 Precautions – Outdoor Installation : Leaking expected at connected cable on outdoor installation. Use the waterproof rubber tape winding up on cable connection as following picture. 1) Connect cables. 2) Winding rubber tape with half overlay on external cable jacket (A) and cable connection. The tape material butyl rubber is extended more than double size.
-
Page 17: Getting Started
4. Getting Started 4.1. PC Requirement Audio/Video streaming data received from IP Camera can be displayed or stored in a PC running client programs. Minimum requirement of the PC is described below: Minimum Requirement Recommended Specification Intel Core i3 3Ghz Intel Core i7 Main Memory Operating System... -
Page 18: Install Ip Installer And Set Ip Parameters On Ip Camera
4.2.2. Install IP installer and set IP parameters on IP Camera 1. Please insert the Setup CD into your CD-ROM drive, and then please setup Figure 4-2-1. IP Installer Setup 1 2. Please click ‘Install’ button to begin the Installation. Figure 4-2-2. - Page 19 installation. Please double click XNET camera on the list. Figure 4-2-4. IP Installer Start box 5. Select the camera of which you wish to change the IP address and click (Set IP Address) button to bring up the following box in Figure 4-2-5. Figure 4-2-5.
- Page 20 6. When you enter the IP address and click Set button, the box shown in Figure 4-2-5 will appear. Figure 4-2-6. Select Network Adapter Box Select the adapter and click ‘Select’ button to change the IP address of the camera. Rev.1.4...
-
Page 21: Remote Video Connection To Ip Camera
1. Connection through Web Viewer Web Viewer offers simplest way of video connection to IP Camera. For video connection, enter the IP address of MPC1070PN in the URL window of Internet Explorer as: Can be omitted the [e.g.] Port 80 default port of 80 [e.g.] Port 8080... -
Page 22: Additional Settings Through Connection To The Admin Page
2. Connection through NVR2 NVR2 is a multi-channel CMS program for IP camera or Video server. Install NVR2 on remote PC to connect to these products. It is needed to assign connection information to NVR2 program before connection. Details for the NVR2 can be found in [NVR2 User’s Guide]. Figure 4-7. -
Page 23: Trouble Shooting
5. Trouble Shooting 5.1. No power is applied In case of Standard PoE (Power over Ethernet) Power supply through standard PoE is possible only when the following conditions are met. 1. Standard PoE is supported on the product. 2. The LAN switch supports standard PoE. Make sure that both the IP camera and the LAN switch support standard PoE (IEEE 802.3af) ... -
Page 24: Windows 7
5.3. Windows 7 Windows 7 users need to configure UAC (User Access Control) and Privilege Level for proper recording and still video capture in NVR and Web Viewer. 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Change User Account Control setting”... -
Page 25: Technical Assistance
5.4. Technical Assistance If you need any technical assistance, please contact your dealer. For immediate service, please provide the following information. 1. Model name 2. MAC address and Registration number 3. Purchase date 4. Description of the problem 5. Error message Rev.1.4... -
Page 26: Appendix A - Important Notice In Exchanging Sd Card (Micro Sd)
Appendix A – Important Notice in Exchanging SD Card (Micro SD) SD Card is a non-volatile memory device for storing video and audio data on the product. Continued writing to the SD Card will cause wear-off of the memory cell. When you plug out the SD Card for replacement or other purpose, follow the steps below in order to prevent data loss or crash of the SD Card.
Need help?
Do you have a question about the MPC1070PN and is the answer not in the manual?
Questions and answers