Related Manuals for Taurus TT-SB 200
Summary of Contents for Taurus TT-SB 200
- Page 1 250W BAND SAW INStruCtIoN MANuAl MoDel NuMBer tt-SB 200 After SAleS Support tel:1300 922 271 N26704 eMAIl: service.australia@einhell.com...
-
Page 2: Table Of Contents
Congratulations on choosing to buy a TAURUS® product. All products brought to you by TAURUS® are manufactured to the highest standards of performance and safety, and, as part of our philosophy of customer service and satisfaction, are backed by our comprehensive Year Warranty. - Page 3 After Sales Support TEL: 1300 922 271 EMAIL: service.australia@einhell.com...
- Page 4 After Sales Support TEL: 1300 922 271 EMAIL: service.australia@einhell.com...
- Page 5 After Sales Support TEL: 1300 922 271 EMAIL: service.australia@einhell.com...
- Page 6 After Sales Support TEL: 1300 922 271 EMAIL: service.australia@einhell.com...
-
Page 7: General Safety Rules
1. General Safety Rules e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. WARNING! Read all instructions Failure to follow all f. Dress properly. Do not wear loose clothing or instructions listed below may result in electric shock, fire and/ jewellery. -
Page 8: Special Safety Rules
2. Special Safety Rules 13. Avoid abnormal working postures! Make sure you stand squarely and keep your balance at Important: Whenever you use electric tools it is imperative all times. to take basic safety precautions in order to reduce the risk of fire, electric shock and personal injury. - Page 9 23. Wear safety gloves whenever you carry out any 45. If the table insert is worn, replace it. maintenance work on the blade! 46. Never operate the machine if either the door protecting 24. In the case of mitre cuts when the table is tilted, the guide the blade or the detachable safety device are open.
-
Page 10: Layout
3. Layout (Figures 1/2) 5. Proper use 1. ON/OFF switch The bandsaw is designed to perform longitudinal and cross 2. Power cord cuts on timber or wood-type materials. To cut round materials you must use suitable holding devices. The machine is to be 3. -
Page 11: Technical Data
6. Technical data 7. Before putting the machine into operation Voltage: _______________________________ 230 V ~ 50Hz Power: _____________________ S1 180 W S2 15 min 250 W • M ake sure the machine stands securely, i.e. bolt it to a Ideal speed no: ___________________________ 1400 min workbench or solid base. There are two holes for this purpose in the machine foot. - Page 12 • S lowly turn the upper blade pulley (8) clockwise by hand. and the blade (26). The blade must not jam. The blade (26) should run in the middle of the pulley. If • Re-tighten the Allen screws (37). it does not, you will have to adjust the tilt of the upper • T urn the upper blade pulley (8) several times in a blade pulley (8).
-
Page 13: Control Elements
13 8.7. Blade selection • Lift out the worn table insert (Fig.16/Item 17). The blade supplied with the bandsaw is designed for all- • F it the replacement table insert by following the above purpose use. When you select a blade you should have regard in reverse. to the following criteria: 8.11. Extractor sockets • U se a narrow blade to cut tighter radius than you can with The bandsaw is equipped with extractor sockets (Fig.1/Item 6) a wider blade. -
Page 14: Transport
11. Transport 10.1. Longitudinal cuts (Fig.20) Longitudinal cutting is when you use the saw to cut along the To transport the bandsaw, hold the supporting foot grain of the wood. (Fig.1/Item 5) with one hand and the frame (Fig.2/Item 25) •... - Page 15 After Sales Support TEL: 1300 922 271 EMAIL: service.australia@einhell.com...
- Page 16 07/2013 (01) 43.080.05_11013 After Sales Support TEL: 1300 922 271 EMAIL: service.australia@einhell.com...
Need help?
Do you have a question about the TT-SB 200 and is the answer not in the manual?
Questions and answers