Related Manuals for IDS GigE uEye FA
Summary of Contents for IDS GigE uEye FA
- Page 1 GigE uEye FA Technical Manual IDS Imaging Development Systems GmbH Dimbacher Str. 6-8 D-74182 Obersulm, Germany T: +49 7134 96196-0 E: info@ids-imaging.com W: http://www.ids-imaging.com...
-
Page 2: Table Of Contents
5 GigE uEye FA ............................ 8 5.1 Ambient conditions ........................9 5.2 System requirements ......................... 10 5.3 Connecting a GigE uEye FA ....................... 10 6 Mechanical specifications ........................ 11 7 Optical specifications ........................12 7.1 Immersion depth for lenses ......................12 7.2 Position accuracy of the sensor .................... -
Page 3: Preface
Please contact your local IDS distributors for first level support in your language. For a list of IDS distributors worldwide please go to our website http://www.ids-imaging.com. -
Page 4: Symbols And Hints
Technical Manual: GigE uEye FA 2 Symbols and hints This symbol indicates hints with useful information for better understanding and using features and functions. This symbol indicates important warnings for product safety to prevent damage. This symbol indicates important warnings for personal safety to prevent injury. -
Page 5: Safety Instructions
All warranty will be spoiled in this case. Intended use IDS industrial cameras are to be used to capture images for visualization and image processing tasks. They are designed for use in industrial environments. Please comply with the requirements for the proper use of this product. - Page 6 Technical Manual: GigE uEye FA Operation and power supply The camera power supply must meet the requirements for SELV (safety extra low voltage)/LPS (limited power source) or ES1/PS2. WARNING! Non-approved power supplies for camera operation may cause painful or dangerous electric shock.
-
Page 7: Standards And Directives
Technical Manual: GigE uEye FA 4 Standards and directives (only valid for devices with housing) IDS Imaging Development Systems GmbH hereby confirms that this product has been developed, designed and manufactured in compliance with the following European directives · 2014/30/EU: EMC - Electromagnetic compatibility ·... -
Page 8: Gige Ueye Fa
Technical Manual: GigE uEye FA 5 GigE uEye FA Housing/board-level Dimensions height x width x length 41 x 53 x 42.7 mm Mechanical specifications Mechanical specifications IP code IP 65 · Protection against penetration of dust: No ingression of dust at a vacuum of 20 mbar in the housing ·... -
Page 9: Ambient Conditions
Humidity* 20 % … 100 %, relative, non-condensing * Only if GigE uEye FA lens tube and IP65/67 cables are used Non-condensing means that the relative air humidity must be below 100 %. Otherwise, moisture will form on the camera surface. If, for example, air has a relative humidity of 40 % at 35 °C (95 °F), the relative humidity will increase to over 100 % if the air cools down to 19.5 °C (67 °F);... -
Page 10: System Requirements
Depending on the sensor model, the camera performance may be limited with the minimum system requirements. 5.3 Connecting a GigE uEye FA Check the power supply to the camera. Connect the camera to to a Gigabit Ethernet port on the PC either directly or using switches. -
Page 11: Mechanical Specifications
Therefore, first unplug the GigE and/or I/O cable from the camera. Note on the IP 65/67 standards The GigE uEye FA housing version is IP 65/67 compliant. The following requirements must be met for conformance to the IP 65/67 standards: ·... -
Page 12: Optical Specifications
Technical Manual: GigE uEye FA 7 Optical specifications · Immersion depth for lenses · Position accuracy of the sensor 7.1 Immersion depth for lenses Some C-mount lenses reach deep into the camera flange. This may cause the lens to push against the back of the filter glass inside the camera or even make it impossible to screw in the lens. -
Page 13: Position Accuracy Of The Sensor
Technical Manual: GigE uEye FA 7.2 Position accuracy of the sensor The following illustrations show the tolerance margins of the sensor position relative to the outer camera housing. A maximum error in all directions (rotation, translation) cannot occur at the same time. -
Page 14: Electrical Specifications
BI_DD- rear view MDX2- BI-DC- MDX2+ BI_DC+ The M12 connector of the GigE uEye FA complies with the IEC/PAS 61076-2-109 standard. 8.2 Pin assignment I/O connector 8-pin Binder connector (Binder series 712: 09-0427-020-08) Description Trigger input with optocoupler (+) Input power supply (VCC) 12-24 V DC General purpose I/O (GPIO) 1, 3.1 V... -
Page 15: Digital Input Wiring
Choose the size of the cable in such a way that the supply voltage available at the input of the camera is at least 12 V. To supply the GigE uEye FA camera with power using PoE or PoE+, you can use PoE injectors or switches that are compatible with IEEE standard 802.3af or IEEE standard 802.at. -
Page 16: Digitaloutput Wiring
Technical Manual: GigE uEye FA Digital input wiring Fig. 7: Wiring of the trigger connector 8.4 Digitaloutput wiring Symbol Min. Typ. Max. Unit Recommended supply voltage Collector-emitter saturation voltage 0.03 0.15 CE(SAT) Collector-emitter breakdown voltage (BR)CE Collector current continuous The digital output is galvanically isolated using an optocoupler to protect the camera and the PC against surges. - Page 17 Technical Manual: GigE uEye FA Fig. 8: Wiring of the digital output as an open collector output Fig. 9: Wiring of the digital output as an open emitter output January 2020...
-
Page 18: General Purpose I/O Wiring
Technical Manual: GigE uEye FA 8.5 General Purpose I/O wiring The two programmable GPIOs (general purpose I/O) can be used as inputs or outputs. This selection is made by software using the corresponding functions. Please observe the following criteria: Symbol Min. - Page 19 Technical Manual: GigE uEye FA GPIO wiring as output Fig. 11: GPIO wiring as output (1) Fig. 12: GPIO wiring as output (2) January 2020...
-
Page 20: Status Led
Technical Manual: GigE uEye FA 9 Status LED Fig. 13: Status LEDs The camera has two LEDs that indicate information of the current status. · LED 1: camera status (two-color) · LED 2: Network status (two-color) LED 1 Camera is off/no power... -
Page 21: Filter Glasses
Every camera model is available with different filter variants such as daylight cut filters (type DL). The filter type is given at the end of the model name. The following table shows an overview of the different optical filters used in IDS cameras: Refractive... -
Page 22: Cleaning The Filter Glasses
The filter glasses may only be cleaned from the outside. If you remove the glasses, the sensor might get soiled.IDS Imaging Development Systems GmbH is not liable for any damage to the sensor resulting from removal of the filter glasses. - Page 23 Technical Manual: GigE uEye FA use purified nitrogen from nitrogen bottles. · Only use lint-free wipes or cotton-free swabs for cleaning. Never touch the filter glasses with your bare fingers because often, fingerprints cannot be removed completely afterwards. · We recommend to use pure alcohol for cleaning. 100% isopropyl alcohol evaporates without leaving any residues.
-
Page 24: Index
Technical Manual: GigE uEye FA Windows - A - Output Ambient conditions digital - C - - P - Contact Pin assignment Plain glass filter - D - - S - Daylight cut filter Dimensions Safety Sensor - E -...
Need help?
Do you have a question about the GigE uEye FA and is the answer not in the manual?
Questions and answers