Sealey SM222 Quick Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SafeTy
eLeCTRICaL SafeTy
1.1.
WaRNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey dealer.
if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
8
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. GeNeRaL SafeTy
WaRNING! ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
‰
equipment.
Familiarise yourself with product application and limitations, as well as the specific potential hazards peculiar to the cleaning tank.
9
WARNING! disconnect the cleaning tank from the mains power before changing accessories, servicing or performing any maintenance.
‰
DO NOT unplug machine with wet hands.
8
Maintain the cleaning tank in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
9
locate the cleaning tank in an adequate working area for its function. ensure the cleaning tank stands on a firm level surface. Keep
9
area clean and tidy and free from unrelated materials. ensure the area is well ventilated and has adequate lighting.
Keep the cleaning tank away from heat sources such as heater, sparks, open flames etc.
9
Keep the tank clean. Remove and clean the filter regularly for best and safest performance.
9
ensure there are no flammable or combustible materials near the work area.
9
WaRNING! Always wear approved eye or face protection when operating the cleaning tank along with protective gloves (see Sealey
‰
Catalogue for suitable gloves, we recommend part no. SSP32)
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.
9
Wear appropriate protective clothing.
9
Maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
Avoid accidental starting of the cleaning tank. ensure that it is unplugged from the mains supply when not in use.
9
In case of fire in the cleaning tank, close the lid. DO NOT attempt to remove parts, or the cleaning tank.
9
DO NOT use the cleaning tank for any purpose other than for which it is designed.
8
DO NOT use the cleaning tank where there are flammable liquids, solids or gases.
8
© Jack Sealey limited
Mobile Parts Cleaning Tank with Brush
Model no:
Wear protective Wear protective
gloves clothing
Original Language Version
SM222
electrical shock
hazard
Recommended fuse rating
3 Amp
SM222 Issue 2 (HF) 29/06/18