Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for SOMFY Sunea io
Summary of Contents for SOMFY Sunea io
- Page 1 Sunea io Installation guide...
-
Page 2: Table Of Contents
5.6. Checking the settings 1. INTRODUCTION The Sunea io motor is designed for use with all types of awning ( with cassette or non-cassette). What is io-homecontrol® ? The· Sunea io uses io-homecontrol®, the new universal and secure wireless communication protocol, shared by worldwide leaders in the world of home equipment. -
Page 3: Safety
Any use outside the sphere of application specified by SOMFY is forbidden. This invalidates the warranty and discharges Somfy of all liability, as does any failure to comply with the instructions given herein. Never begin installing without first checking the compatibility of this product with the associated equipment and accessories. -
Page 4: Motor/Tube Assembly
3 x 0,75 mm 230 V table below: 50 Hz 3 x 1,5 mm 230 V ~ 50 Hz Motor cable 1 Brown Live (P) 2 Blue Neutral (N) 3 Yellow/Green Earth ( ) Copyright © 2010 Somfy SAS. All rights reserved. -
Page 5: Commissioning
Sunea io 5. COMMISSIONING This guide describe only the comisioning using a Somfy io local control point as Situo io. For comisioning using other io control point, refer to the corresponding guide. 5.1. Identifying setting steps already completed Only one motor can be powered at a time. -
Page 6: Adjusting The End Limits
Press the “my” button again until the awning makes a movement: the end limits have been programmed, go to chapter “Programming the first Somfy io local control point”. 5.4.2. Settings for non-cassette awnings For non-cassette awnings, the upper and lower end limits must be set. -
Page 7: Programming The First Somfy Io Local Control Point
5.6. Checking the settings Check the setting of the upper and lower end limits using the Somfy io local control point. 6. USE 6.1. Standard operation 6.1.1. Favourite position (my) Definition... -
Page 8: Additional Settings
Sunea io 6.3. Data feedback After each order, the Sunea io sends a message. The information is managed by the io bi-directional control points. 7. ADDITIONAL SETTINGS 7.1. Favourite position (my) 7.1.1 Setting or modifying the favourite position (my) The procedure for setting or modifying the favourite position (my) is the same. -
Page 9: Advanced Functions
This function allows the fabric tension to be released after the cassette awning is closed. The procedure for activating and deactivating the “Back release” function is the same. For safety reasons, this function can only be activated or deactivated by the Somfy io control point in 3 situations: •... -
Page 10: Tips And Recommendations
Fit the crown correctly. too soon. The end limits have been incorrectly set. Readjust the end limits 8.2. Replacing a lost or broken Somfy io control point Refer to the corresponding guide. Copyright © 2010 Somfy SAS. All rights reserved. -
Page 11: Restoring The Original Configuration
230 V ~ 50 Hz Operating temperature - 20 °C to + 70 °C Protection rating IP 44 Maximum number of connected io control points and io sensors Safety level Category I Copyright © 2010 Somfy SAS. All rights reserved. - Page 13 Tel: +39-024847181 Tel. +351 229 396 840 United Arab Emirates: Czech Republic: Japan: Romania: Somfy Gulf Jebel Ali Free Zone Somfy SRL Tel: +971 (0) 4 88 32 808 Somfy, spol. s.r.o. SOMFY KK Tel: (+420) 267 913 076 - 8 Tel: +81 (0)45 481 6800 Tel.: +40 - (0)368 - 444 081...
Need help?
Do you have a question about the Sunea io and is the answer not in the manual?
Questions and answers