Panasonic Technics SL-1600M Service Manual

Panasonic Technics SL-1600M Service Manual

Direct drive automatic turntable system

Advertisement

Specifications

Turntable section
Type:
Direct Drive Automatic Turntable System,
A u t o m a t i c start, A u t o m a t i c return, Automatic
shut-off and M E M O -R E P E A T play Manual
Drive method:
Direct D r ~ v e
M o t o r :
Back Electromotive Force Frequency
Generator servo D C m o t o r
employing one chip IC
Turntable platter:
Turntable speeds:
Pitch controls:
Individual adjustment controls. 10%
adjustment range
Wow and f l u t t e r :
0.025% W.R.M.S (JIS C5521)
( D I N 45507)
Rumble:
- 50 d B ( D l N 4 5 5 3 9 A )
- 73 d B ( D I N 45539B)
Tonearm section
Universal tubular arm, staticbalanced t y p e
T y p e :
Effective length:
2 3 0 m m (9-1/16',)
Overhang:
1 5 m m
Specifications are subject t o change w i t h o u t notice for further improvement.
Weights and dimensions shown are approximate.
19/32")
Panasonic Company
Division of Matsushita Electric
Corporation of America
One Panasonic Wav. Secaucus,
www.vinylengine.com
Direct drive automatic Turntable System
Friction:
Effective mass:
Tracking error angle:
Offset angle:
Adjustable stylus
pressure range:
Cartridge weight range: 5 t o 1 1 g
Head shell weight:
General
Power supply:
Power consumption:
Dimensions:
Wegiht:
Hawaii 96817
ORDER NO. SD7702-1182
7 m g (horizontally and vertically)
2 2 g (6.0 g cartridge weight 1.75 g stylus
pressure)
W i t h i n +3O at t h e p o i n t o f 145
(5-45164" ) f r o m t h e
center
w i t h i n
at t h e p o i n t o f 5 5 m m
center
9.5 g
A C 1 2 0 V . 5 0 o r 6 0 H z
6 W
12.5 x 45.3 x 36.9 c m
14-15/16 x 17-12/16 x 14-9/16 inches)
9.0 kg ( 1 9.8 ibs.)
Ontario, Canada M9W
1
mm
I
1 B5

Advertisement

Table of Contents
loading

Summary of Contents for Panasonic Technics SL-1600M

  • Page 1: Specifications

    2 3 0 m m (9-1/16',) Wegiht: 9.0 kg ( 1 9.8 ibs.) Overhang: 1 5 m m 19/32") Panasonic Company Division of Matsushita Electric Corporation of America Hawaii 96817 Ontario, Canada M9W 1 B5 One Panasonic Wav. Secaucus, www.vinylengine.com...
  • Page 2: Parts Identification

    Parts identification Hinge Fig. 1 Pitch control knobs Turntable base Assembly and set-up Apply two or three drops of oil to the motor shaft from the panel cover. using the furnished oil container. (See Fig. (2) Draw out three connectors. Although the unit has been lubricated before shipping For separation of the body from the main from the factory, apply a few drops of oil to the...
  • Page 3 Adjustments Adjustment of the arm lift height (See Figs. 4 and The arm lift height (distance between the stylus tip and record surface when cueing lever is raised) has been adjusted at the factory before shipping to ap- 6" proximately to 10 mm (311 to 25/64").
  • Page 4: Operating Principle

    power source affects the strobe illuminator, the strobe The state under which the strobe dots seem to be dot pattern also seems t o fluctuate t o a certain extent. stationary represents the correct number of revolu- But the unit is not affected by -the fluctuations of the tions.
  • Page 5: Explanation Of Each Part

    Explanation of each part 1. B.F.G. METHOD (BACK ELECTROMOTIVE FORCE FREQUENCY GENERATOR) 3. OPERATION CONTROL CIRCUIT Making use of the back electromotive force that is The operation control circuit functions as a control out- generated in the drive coil winding of the motor as a put voltage control keeping the rotational speed of the frequency generator, the frequency of the frequency turntable constant with regard to the start of turntable...
  • Page 6 www.vinylengine.com...
  • Page 7 www.vinylengine.com...
  • Page 8 EXPLODED VIEW OF TURNTABLE www.vinylengine.com...
  • Page 9 EXPLODED VIEW OF TURNTABLE www.vinylengine.com...
  • Page 10 www.vinylengine.com...
  • Page 11 www.vinylengine.com...
  • Page 12 www.vinylengine.com...

This manual is also suitable for:

Technics sl-1600mc

Table of Contents