Sloan Solis EAF-275 Series Installation Instructions

INSTALLATION INSTRUCTIONS FOR ELECTRONIC
SENSOR ACTIVATED LAVATORY FAUCETS
EAF-275 Series
Solar Powered
with Battery Backup
Sensor Activated
Lavatory Faucets
(Models shown with ISM Integral Spout Mixer)
Sloan Valve Company warrants its Optima EAF-275, EAF-250 and EAF-200 Series Electronic Hand Washing Faucets to be made
of first class materials, free from defects of material or workmanship under normal use and to perform the service for which they
are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three years from
date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to
be thus defective if returned to Sloan Valve Company, at customer's cost, and this shall be the sole remedy available under this
warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or
organizations who purchase Sloan Valve Company's products directly from Sloan Valve Company for purpose of resale. This
warranty does not cover the life of the battery.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE
COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
FAUCET ROUGH-IN
MODELS EAF-200/250/275 ‡
2.2 gpm (8.3 Lpm) Max. Flow Aerator ‡
Faucets with Single Line Water Supply
SPOUT
1-3/16" (30 mm) MIN.
DIA. HOLE REQUIRED
O-RING
GASKET
RETAINER
NUT
LONG FLEX HOSE
TEMPERED
SUPPLY
If a connection to separate hot and cold
water supplies is desired, then a Bak-Chek
tee fitting (not supplied) must be used prior
to connecting to the faucet.
‡ EAF-275 Series Faucets are furnished with a 0.5 gpm (1.9 Lpm) Aerator Spray Head.
EAF-250 Series
Battery Powered
Sensor Activated
Lavatory Faucets
EAF-200 Series
Transformer Powered
Sensor Activated
Lavatory Faucets
LIMITED WARRANTY
MODELS EAF-200/250/275-ISM ‡
MODELS EAF-200/250-ISM-IC
MODELS EAF-200/250-ISM-DPU-IC
2.2 gpm (8.3 Lpm) Max. Flow Aerator ‡
Faucets with Hot and Cold Water Supply
1-1/2" (38 mm)
MAX. DECK
THICKNESS
13" (330 mm)
HOT
SUPPLY
®
Code No. 0816490
Rev. 1a (11/06)
SPOUT
(Can Be Set and Removed)
1-3/16" (30 mm) MIN.
DIA. HOLE REQUIRED
O-RING
GASKET
RETAINER
NUT
13" (330 mm)
LONG FLEX HOSE
FAUCET VARIATIONS
-ISM Integral Spout Mixer (All Series)
-Click Feature (EAF-200/250 Series)
-IC
-DPU Drain Pop Up (EAF-200/250 Series)
-P Plug-in Transformer (EAF-200 Series)
-LT Less Transformer (EAF-200 Series)
PRIOR TO INSTALLATION
Prior to installing the Sloan Optima EAF-275/
EAF-250/EAF-200 Series Faucets, install the items
listed below. Also, refer to rough-in illustrations.
• Lavatory/sink
• Drain line
• Hot and cold water supply lines or pre-tempered
water supply line
Important:
• ALL PLUMBING SHOULD BE INSTALLED IN
ACCORDANCE WITH APPLICABLE CODES AND
REGULATIONS.
• FLUSH ALL WATER LINES PRIOR TO MAKING
CONNECTIONS.
• KEEP THREAD SEALANT OUT OF YOUR WATERWAY
TO PREVENT COMPONENT PART DAMAGE! DO NOT
USE ANY SEALANT ON COMPRESSION FITTINGS.
Trim Plates
When the EAF Faucet is installed on a sink that has
three (3) hole punchings, a Trim Plate should be used.
Trim Plates must be specified and ordered separately.
ETF-312-A Trim Plate for 4" (102 mm) Centerset Sink
ETF-510-A Trim Plate for 8" (203 mm) Centerset Sink
TOOLS REQUIRED FOR INSTALLATION
• 13 mm open end wrench or nut driver for faucet
retainer nut
• 3/4" open end wrench for female end of flex hose
FAUCET SPOUT
DIMENSIONS
MIXING LEVER
1-1/2" (38 mm)
MAX. DECK
THICKNESS
5-11/32"
(136 mm)
COLD
SUPPLY
2-1/16"
(52 mm)
4-11/32"
(110 mm)
24º
2-1/16"
(52 mm)
2-9/16"
(65 mm)