Advertisement
Advertisement
Table of Contents
Summary of Contents for CAMPARK R10
- Page 1 Campark R10 Touch Screen Streaming Video Rear View Mirror 190121...
-
Page 3: Important Notice
Important Notice: NOTICE : Due to the high power consumption of this unit, it should always be connected to an external power supply. This unit will not power on without external power supply. This product is intended for using in motor vehicle only. Do NOT install the device where it might block the driver’s view of road (including the mirrors) or the deployment of the airbag. -
Page 4: Installation Guide
Installation Guide 1.B efore installation, please insert a high speed memory card in the unit and format the memory card in the unit setting, also do a simple test to make sure the unit is working perfectly. 2. Mount the mirror over the original rearview mirror and use the included rubber ring to fix it(The front lens base is stretchable, it can be pulled out sideways when necessary ). - Page 5 6. The rearview camera should be installed at the rear end of the car, normally the best place is above the number plate. The camera can be fixed with the sticker or the screw. You can see the diagram for reference. 7.T he excess RED lead near the rear view camera is used for reverse status sensing.
- Page 6 b. Mount it directly on the car panel, if you are driving a truck or a van and the number plate position is too low. You can mount the camera directly on the car panel with double-sided adhesive and screws, like an ordinary rear view camera.
- Page 7 9.R oute the camera cable to the front of the car and connect it to the main unit. There are 2 pictures for reference. (NOTICE: Holes might need to be drilled to pass the cable.) 10.A fter the installation is completed, please start the engine and have a test run, make sure all functions are working.
- Page 8 Adjust the Reversing Camera Adjust the reversing camera angle. The best angle is the camera can cover the rear of the car and the ground surface under the rear end. Notice: When the car is in reversing, the rear camera will automatically display in full screen, and turn to the lowest angle, so you can see the ground surface under the rear end while reversing.
- Page 9 Interface and Button Functions GPS interface (Optional) Rear Camera interface Mini USB Memory Card slot Power RESET...
-
Page 10: Power Button
Power button NOTICE : When the external power supply cuts off (the engine turns off), the camera will immediately dim the screen display, and power off within 10 seconds (There will be a BEEP prompt when powers off) Power On/ Power Off Long press the power button for 3 seconds to power on or power off the unit Turn off / Turn on Screen Display... - Page 11 The main interface and Operations If the unit is power properly, when you start the car engine, the unit will automatically power on and start recording. If you want to operate the recorder, touch the screen. The following toolbar will show up on the screen. Slide vertically to move 20:05 the image up and down.
-
Page 12: Video Playback
Video playback Click the Playback Icon in the toolbar to enter playback mode. There are 3 folders in the playback mode 001/143 FILE200211-003540F.MOV FILE200211-003540F.MOV FILE200211-003540F.MOV FILE200211-003540F.MOV FILE200211-003540F.MOV 1. Front Camera Video 2. Locked Files 3. Rear Camera Video... -
Page 13: Featured Function
Featured Function Dual Recording The R10 mirror comes with dual channel lens, they can record video in 1080P + 720P simultaneously, you can setup the front or the rear camera record in 1080P , and the other one in 720P. -
Page 14: Parking Monitor
Parking Monitor The Parking Monitor is used to protect your car after parking, with this function on, after you stop the car and the unit turns off, it stays in standby, when unit detects significant shock, it will automatically turn on and take a 15 seconds short video, then shut down automatically. -
Page 15: Gps Function
GPS Function The GPS function is optional on the R10 camera, with the optional GPS module plugged in, the R10 can display current speed and heading direction on screen. You can enter the setup menu and check the GPS signal status. - Page 16 Setting Menu and Options Setup Option How it works Adjust video resolution, F for Front Camera, R for rear camera. 1080P (F)+720P(R) / Resolution When dual recording is off, only the 720P (F)+1080P(R) / front camera will record video in 1080P or 720P.
- Page 17 Common Problem and Solution Recorder shows memory full, unable to loop video, etc. 1. First, when a new memory card is used for the first time on the machine. Please format the memory card in the camera first. Or the memory card is previously used on another type of device, it needs to be formatted when used on this camera.
- Page 18 If You Have Any Questions or Problems. Pease contact us by USA& Canada support@campark.cc Europe eu.support@campark.cc uk.support@campark.cc Australia au.support@campark.cc More Safe Guarantee with campark.We will offer prompt and authoritative reply within 24 hours and try our best to resolve your problem ASAP.
Need help?
Do you have a question about the R10 and is the answer not in the manual?
Questions and answers