Philips CE120X/78 Quick Start Manual page 2

3
English
1 Black To a metal surface of the car
First connect the black ground
(earth) lead, then connect the
Overview of parts
yellow and red power supply
leads.
These are the supplied parts needed to connect
2 To the electric antenna control
Blue
and install this unit.
lead or power supply lead of the
a Carry case with front panel stored inside antenna booster
If there is no electric antenna or
b Trim plate
antenna booster, or it is manually
c Standard connector operated telescopic antenna, it
is not necessary to connect this
d Disassembly tool x 2 pcs
lead.
e Rubber cushion
3 Yellow To the +12V car battery which
is energized at all times .
f Screw x 4 pcs
4 Pink To telephone mute terminal (if
g Mounting bolt
any) .
5 Red To the +12V power terminal
Connect wires: ISO connectors which is energized in the ac-
cessory (ACC) position of the
ignition switch
If there is no accessory position,
1
Pull out the ISO connectors from car
connect to the +12V car battery
dashboard and connect them to the bigger
terminal that is always live. Be
end of the supplied standard connector.
sure to connect the black ground
2
Connect the other end of the supplied
(earth) lead to a metal surface of
standard connector to the unit. the car fi rst.
3
Do the other connections, if applicable. 6 Green/ Left speaker (Rear)
black
1 Antenna To antenna
strip
2 Rear line out To amplifi er line in (right) 7 White/ Left speaker (Front)
black
(right)
strip
3 Rear line out To amplifi er line in (left)
8 Gray/ Right speaker (Front)
(left)
black
strip
Connect wires: without ISO
connectors
9 Purple/ Right speaker (Rear)
black
1
Cut off the bigger end of the supplied
strip
standard connector.
3
2
Check the car's wiring carefully and connect Connect the supplied standard connector to
them to the supplied standard connector.
the unit.
4
Do the other connections, if applicable.
4
Detach the front panel
1 Antenna To antenna
2 Rear line out To amplifi er line
You can detach the front panel to deter theft.
1
(right) in (right)
Press to release the panel.
2
3 Rear line out To amplifi er line Pull the panel towards you to detach it from
the chassis.
(left) in (left)
3
Store the panel in the supplied carry case to
protect it from dirt or damage.
Attach the front panel
Turn on
1
Attach the trim plate.
1
Press to turn on the unit.
2
Insert the left side of the panel in the chassis
• To turn off the unit, press
until it is correctly engaged.
seconds.
3
Press the right side of the panel until it is
locked into place.
Set clock
1
Press MENU / DISP for 3 seconds.
Mount into the dashboard 2
Press DBB or SEARCH repeatedly until
the currently clock is displayed.
1
Ensure that car dashboard opening is within 3
Turn in clockwise direction to set hour.
these measurements:
Turn in anti-clockwise direction to set
• If the car dashboard is bigger, the sup-
minute.
plied mounting sleeve is not suitable for
4
Press to confi rm.
the car. Remove the mounting sleeve
with the removal keys and consult a
professional for advice.
2 View clock
If the car does not have an on-board drive
or navigation computer, disconnect the nega-
1
Press MENU / DISP repeatedly until the clock
tive terminal of the car attery.
is displayed.
• If you disconnect the car battery in
a car that has an on-board drive or
navigation computer, the computer may
Tune to a radio station
lost its memory.
• If the car battery is not disconnected,
1
Press SOURCE to select Tuner.
to avoid short-circuit, ensure that bare
2
Press DBB or SEARCH to select band:
wires do not touch each other.
3 [FM1] , [FM2] , [FM3] , [AM1] , or [AM 2] .
Connect the supplied mounting bolt to the
3
unit.
Press LOC/DX to select tuner sensitivity:
4 [LOCAL] (local): Only station with strong
Place the supplied rubber cushion over the
end of the mounting bolt. signal can be broadcast.
[DX] (distance): Stations with strong and
5
Slide the unit into the dashboard until you
weak signals can be broadcast.
hear a click sound.=
4
Press or to tune to a radio station
6
Reconnect the negative terminal of the car
manually.
battery.
The radio station is broadcast.
»
• To search for radio station automatically,
press or for 3 seconds.
Insert USB device
1
Open the cover marked on the front
panel.
2
Insert the USB device into the USB socket.
The unit star ts playing from the USB
»
device automatically.
Insert SD/MMC card
1
Open the cover marked on the front
panel.
for 3
2
Insert the SD or MMC card into the card
slot.
The unit starts playing from the SD/MMC
»
card automatically.
Control play
• To select a folder, press DBB or SEARCH
.
• To skip to a track, press or .
• To search within a track, press or for
3 seconds.
• To pause, press 1 , . To resume, press 1 ,
again.
5
6
7