VS-60HS12U / CH About LED light source VS-60HS12U uses LED of 4 chips composition for the light source. However, if a part of LED chip breaks down, VS-60HS12U becomes POWER OFF or the brightness of breakdown LED decreases. · Illumination information of LED can be confirmed with the status indicator. (page47) 1.1.2 Optional products...
Page 6
MEMORY SCAN H. / V. POSITION CLOCK PHASE AMP. GAIN H=1, V=2 H=2, V=2 etc. Layout setting (page 43) Input signal allocation Window1 Window position / size setting Crop / zoom setting Window priority order setting etc. Finish VS-60HS12U Set-up Manual...
The cubes can be operated with the remote control unit or control software ”Wallaby”(page22). 1.3.1 Remote control unit Face the remote control toward the screen on each cube to control. Or facing to the MASTER cube (page 20) directs other cubes. The supplied cable with the remote control can be connected directly to the wired ...
· [MUTE] button mutes the status bar on test patterns. · When full-bit white test pattern shows, [MUTE] button turns off the LED light source. When press [MUTE] button again or press [TEST] button and the next test pattern shows, turn on the LED light source. VS-60HS12U Set-up Manual...
1.3.3 Menus Basic menu operations TOP menu The TOP menu is displayed by [MENU1] button on the remote control in advanced mode. Starting from the top menu, any lower menus can be choosen. · Allocated short-cut buttons also allow you to access each menu directly, not-through the TOP menu.
Page 10
It can set display layouts. See on page 42 for detail. Short-cut: [MENU2] button SYSTEM SETTING menu It can set an entire monitor / screen condition. See on page 24 and 34 for detail. Short-cut: Press-and-hold [MENU2] button. VS-60HS12U Set-up Manual...
Control panel The control panel has the following functions. Network port Digital / Analog (page 19) input (page 19) Status indicator” (page 47) Standby switch Wired remote port (page 21) Control ports (page 19) (page 7) RS-232 port (page 19) Dipswitches (page 20) REV 1.0...
To prevent cubes from toppling during screen · open/close, use the support base contained in the cube carton boxes when the cubes are not fixed to a base stand or other cubes. Support base VS-60HS12U Set-up Manual...
Handling of the screens · Hold the short sides of the screen frame or the Because the screen is large and heavy, the screen corners when picking up the screen. Holding the should be held carefully. long sides of the frame may damage the screen edge ·...
Screen-holding arm Demounting 1 Pull up the screen handles on both sides to draw the screen unit till locked and put the handles back to the original positions. Screen-drawing Slide lock lever handles (on both sides) Carton tray VS-60HS12U Set-up Manual...
2.3.2 Base stands and cubes assembling Prepare suitable base stands by yourself to fit the 4 Place an adjacent bottom row cube on the base installation site. stand and fix it in the same way. 1 Make base stands both level and plumb by means of 5 Connect these cubes together at 4 points with a level.
2 Mount a screen unit onto the cabinet. Lifting up the screen unit on a skew (about 15°), insert the pins in the u-slot on both sides. Push the lower part of screen down until the screen becomes upright. U-slot VS-60HS12U Set-up Manual...
2.3.4 Screen gaps adjustment 1 Open the screen unit. 4 After the adjustment, tighten the 3 fixing screws 2 Loosen 3 fixing screws for screen adjustment with a which have been loosened in the step 2. 3mm hex key (fixing screws: 1 for horizontal, 1 for ·...
Furthermore, carefully confirm the strength of the fixing areas (wall and floor) of the installation room. The fixing method differs depending on the number of cubes. Wall-fixing brackets Bolts Bolts Anchors Floor-fixing brackets Adjusters After the completion, proceed to “Adjustment” (page 19). VS-60HS12U Set-up Manual...
3.1.1 Connecting Internal control cables connection External control cables connection From the MASTER monitor (page 20), cascade External controllers such as personal computers in CONTROL OUT and CONTROL IN ports sequentially which adjustment software, Wallaby has been installed between monitors with supplied control cables. also can control monitors.
(ON: accept, OFF: reject) slave slave Mater / slave setting MASTER/SLAVE (ON: MASTER, OFF: slave) Wireless remote control invalidation n Set the switch #3 when needed. It can reject wireless remote control, i.e. to avoid controlling other monitors unintentionally. VS-60HS12U Set-up Manual...
3.1.3 Power-on 1 Turn on the main power switch. The monitor goes to standby state. The ON setting of SYSTEM SETTING > MISC. 1 > AUTO POWER ON automatically starts the start-up process (page 35). Main power switch Power socket 2 Press [POWER ON] button on the remote control or press-and-hold the standby switch on the control panel.
IP addresses on the monitors, Wallaby cannot communicate with them through network. · Once the network is established, the IP addresses can be changed by Wallaby. Start-up the application Run the Wallaby software in Windows® start menu etc. VS-60HS12U Set-up Manual...
ID 1 ID 2 System configuration 192.168.100.32 192.168.100.33 System > Configuration Put the information of the monitor configuration to Wallaby. ID 3 ID 4 192.168.100.34 192.168.100.35 Follow the procedure below if you change such starting values of the sequential unit IDs and IP addresses.
A unique IP address can with [ENTER] button. ID 1 ID 2 be assigned on each 192.168.100.32 192.168.100.33 monitor for controlling through network. ID 3 ID 4 192.168.100.34 192.168.100.35 VS-60HS12U Set-up Manual...
H. LOCATION, V. LOCATION It can invert displayed images vertically or horizontally. SYSTEM SETTING > INSTALLATION > H. LOCATION, V. SYSTEM SYNC. LOCATION It can define locations of each monitor in a display wall SYSTEM SETTING > MISC. 2 > SYSTEM SYNC so that the entire wall can be addressed as one big It changes the internal sync frequency according to the monitor as shown below.
-Press ESC button in Grid adjustment mode, it will Screen return to Grid selection mode. Enter Key 3 H-ZOOM Horizontal size can be adjusted by left and right button. ESC Key Grid Adjustment mode Grid select mode VS-60HS12U Set-up Manual...
8 FINE ADJUST 9x9 2. When the shown area of the ‘GEOM CROSSHATCH’ is Normally please adjust in the FINE ADJUST 5x5 mode. If greatly shifted to the screen, adjust H-ZOOM, V-ZOOM necessary, the setting can be fine tuned in the FINE so that the outline of the ‘GEOM CROSSHATCH’...
Page 28
[Adjustment tips] When it is necessary to adjust correctly in FINE ADJUST5x5 mode, please put a mark on the screen according to the following figure. 333.4mm 666.8mm 187.5mm 375.0mm VS-60HS12U Set-up Manual...
The luminance and color can be adjusted to uniform across monitors in a display wall by CSC (Color Space Control) system. The adjustments of BLACK LEVEL, WHITE BALANCE and GRADATION can be combined with it as needed. The CSC technology can directly control the three primary colors to align different color reproduction ranges on each screen.
7 Repeat the step 5 and 6 alternate the effect. To un-mute a color on all until luminance monitors in the same time, press and hold the and tint of all the colors button of the color. get uniformed. VS-60HS12U Set-up Manual...
[Adjustment tips] · Adjust the values so that the sums of the following In the manual color adjustment, blue is always the items don’t exceed 1023 respectively. most difficult to get uniformed. If you have difficulties Sums to get a good result with the procedure above, the R-R (1023) G-R (0) B-R (0) <...
· When you correct these values bigger, especially corner values, a little distance area inside the corrected areas or corners may be brighter. It happens when values are over the range. Reduce the values to improve it. Gradation adjustment areas VS-60HS12U Set-up Manual...
3.4.7 SENSOR While the brightness of each light source varies · This limit can be changed in THRESHOLD FOR individually as time passes, the sensor function FEEDBACK menu. Lower setting keeps the brightness automatically controls the luminance to uniform in a uniformity for a long time while the entire display display wall.
SYSTEM SETTING > MISC. 1 > START MEMORY You can assign the display layout with a display memory number (page 42) that is initially displayed at start-up. The initial setting is OFF. · OFF setting restores the last displayed layout. VS-60HS12U Set-up Manual...
Page 35
SCREEN INDICATION DITHER SYSTEM SETTING > MISC. 1 > SCREEN INDICATION SYSTEM SETTING > MISC. 1 > DITHER Indications on screen can be hidden. The initial settings It can set dithering. The initial setting is ON, which can are to display all the indications. increase gray-scale rendering.
Page 36
· The system memory stores the values for up to 6 windows to be displayed on a monitor. · An analog signal in the daisy chain board can be adjusted when it is displayed on an even number window. VS-60HS12U Set-up Manual...
Input memory menus can adjust each input signal in a window displayed top overlay priority. The settings can be memorized in 128 input memories. [INPUT B] button on the remote control shows INPUT MEMORY menu. Or select INPUT MEMORY in TOP menu. 3.6.1 Basic setting Normally, check and adjust these basic setting items.
Page 38
· MEMORY CALL (page 10) also can select your saved input memories. CLOCK PHASE Analog INPUT MEMORY > CLOCK PHASE Noise on analog images can be minimized. VS-60HS12U Set-up Manual...
3.6.2 Custom setting The following items can be customized more as necessary even though these adjustments are normally not needed. · Set the same values on all monitors in a display wall. · The items with are automatically adjusted optimally at input signal auto-scan. You can adjust them when an incorrect image is displayed after the auto-scan.
Page 40
When choose “OFF”, the filter is canceled. The Film mode can be set when ADAPTIVE mode is selected in INTERLACE menu. The initial setting is AUTO. n AUTO: detect pull-down signal automatically n OFF: turn off 2-3 / 2-2 pull-down signal processing. VS-60HS12U Set-up Manual...
3.6.3 Input memory saving INPUT MEMORY > INPUT MEMORY SAVE The adjusted values can be saved in an input memory. There are 128 memories available. A change in an input memory shows INPUT SETTING SAVE menu, when going back to the TOP menu by [ESC] button.
The entire display wall can be treated as one big resolution monitor with the pixel map regardless of number of monitors (page 25). 1919/1920 3819 Window1 1079 1080 2159 3.7.1 Available layouts One window can be displayed on HS12 series. Window1 VS-60HS12U Set-up Manual...
3.7.2 Layout setting Window select · Under AUTO SCAN ON status (page 35), if you allocate an “input port” as its input signal, the signal DISPLAY MEMORY > WINDOW 1 scan automatically runs whenever input signals are Select a window to adjust among 1. switched over.
· Checking on “Locked” in the right click menu locks the window so that it cannot be dragged. Aspect ratio DISPLAY MEMORY > WINDOW 1 > ASPECT RATIO It can switch window aspect ratio setting. The initial setting is KEEP. VS-60HS12U Set-up Manual...
Page 45
Cropping/zoom Window disabling DISPLAY MEMORY > WINDOW 1 > CROP DISPLAY MEMORY > WINDOW 1 > ENABLED It can clip / zoom in a partial area in an input singal. You can switch the windows disabled (non-displayed) Specify the area position and size. when needed.
In Wallaby, right-click the display memory in the display memory list and click “Delete”. In Wallaby, the right-click menus change the display method in the memory list, the same manner as input memory (page 41). “Refresh” menu refreshes the list. Display memory list VS-60HS12U Set-up Manual...
SYSTEM SETTING MAINTENANCE LED TIMER RESET Light source operating time reset MAX. TEMPERATURE RESET Internal temperature peak value reset MISC. 2 MEMORY INITIALIZE Factory default restoring The monitors indicates current status to users with both “on-screen indicator” which lights in blue on screen and the “status indicator”...
It indicates for 5 seconds in every 5 minutes. on screen and the monitor will shut down in 1 minute. Check surrounding ambient temperature or vents on Abnormal internal temperature error will be shown on the cubes. both on-screen indicator and the error indicator. VS-60HS12U Set-up Manual...
entrap most of the microscopic dust and particulate Screen front surface without any solvents as water or alcohol. · Notice: · Wipe with a lint free soft and dry cloth or with a - Wipe the mirror gently with the central area of the damp cloth using water or alcohol.
5.2.1 On-screen menus The products have following adjustment menus. For other menus, you can refer to “Menus” on page 9. Menu Description · For entire monitor / screen setting · TOP > SYSTEM SETTING System memory menu · 1 memory in an entire monitor ·...
Analog V. sync mask end position setting FRAME LOCK OFF, ON (OFF) External signal sync setting FILM MODE AUTO, OFF (AUTO) Film mode setting INPUT MEMORY SELECT MEMORY INP.001 – INP.128 (INP.001) Input memory save SAVE NUMBER VS-60HS12U Set-up Manual...
Display memory Menu Range (default) Description Page DISPLAY MEMORY WINDOW 1 WINDOW ARRANGEMENT RESET, TILE, DOT BY DOT (RESET) Window auto-arrangement ENABLED OFF, ON (ON) Window non-display setting DVI DIGITAL INPUT DVI ANALOG Input signal allotment INP.001 – 128 H. POSITION -188160 –...
· Read and Save Memories It reads all memories from selected monitors to save in a designated folder. The same number of files as selected monitors will be created in the folder with .bku extension. · Exit It quits the software. VS-60HS12U Set-up Manual...
Page 55
Edit menu · Setting of Wallaby You can hide the following menus with a password. All menus are open and no password is set in default configuration. · Read Parameters It reads out the selected monitors to update the data in the software.
Page 56
Adjustment menus System It sets the system memory (page 24, 34). · Configuration · Maintenance VS-60HS12U Set-up Manual...
Page 58
Misc. 2 Input It sets the input memories (page 37). Input > A/D Setting > Other Setting VS-60HS12U Set-up Manual...
Page 59
Information Display It displays detailed status information (page 10). It sets the display memories (page 42). · System status · Error information REV 1.0...
Cable: Supplied control cables (male – male) to connect between monitors Diagram: Supplied accessories Qty. per unit Hex socket head bolts (M6) Flat washers (for M6) 8 each Spring washers (for M6) Seals for Joint holes 1 sheet Control cable User’s manual Cable ties VS-60HS12U Set-up Manual...
Description Revision date Issue the first edition Dec. 22, 2014 (Rev. 1.0) REV 1.0...
Page 62
Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation in the United States and/or other countries. The names of other products or companies mentioned are registered trademarks or corporate trademarks of the companies written herein. VS-60HS12U Set-up Manual...