(including loss of data, profits, goodwill, or any type of loss or damage suffered as a result of any action brought by a third party) even if such damage or loss was reasonably foreseeable or Xilinx had been advised of the possibility of the same.
• Three VITA 57.1 FPGA mezzanine card (FMC) high pin count (HPC) connectors • USB-to-UART bridge • C bus • PMBus connectivity to onboard digital power supplies VC7203 GTX Transceiver Characterization Board www.xilinx.com Send Feedback UG957 (v1.3) October 17, 2014...
Do not remove the rubber feet from the board. The feet provide clearance to prevent short circuits on the back side of the board. Note: Figure 1-2 is for reference only and might not reflect the current revision of the board. www.xilinx.com VC7203 GTX Transceiver Characterization Board Send Feedback UG957 (v1.3) October 17, 2014...
Caution! When supplying 12V through J2, use only the power supply provided for use with this board (Xilinx part number 3800033). Caution! Do NOT use a 6-pin, PC ATX power supply connector with J2. The pinout of the 6-pin, PC ATX connector is not compatible J2 and the board will be damaged if an attempt is made to power it from a PC ATX power supply connector.
ON position, power is applied to the board and green LED DS11 illuminates (callout 15, Figure 1-2). Onboard Power Regulation Figure 1-3 shows the onboard power supply architecture. VC7203 GTX Transceiver Characterization Board www.xilinx.com Send Feedback UG957 (v1.3) October 17, 2014...
Page 10
7 Series GTX Power Module MGTAVCC 1.05V at 12.0A max MGTAVTT 1.2V at 8.0A max MGTVCCAUX 1.8V at 2.6A max UG957_c1_03_100712 Figure 1-3: VC7203 Board Power Supply Block Diagram www.xilinx.com VC7203 GTX Transceiver Characterization Board Send Feedback UG957 (v1.3) October 17, 2014...
Page 11
12). Transceiver supply voltages cannot be changed from this controller. 3. For information on XADC see 7 Series FPGAs and Zynq-7000 All Programmable SoC XADC Dual 12-Bit 1 MSPS Analog-to-Digital Converter User Guide (UG480) [Ref 1] VC7203 GTX Transceiver Characterization Board www.xilinx.com Send Feedback UG957 (v1.3) October 17, 2014...
Adapter PMBus pod and associated TI GUI. References More information about the power system components used by the VC7203 board are available from the Texas Instruments digital power website [Ref www.xilinx.com VC7203 GTX Transceiver Characterization Board Send Feedback UG957 (v1.3) October 17, 2014...
(Figure 1-5) is provided for the FPGA. A 12V fan is affixed to the heatsink and is powered from the 3-pin friction lock header J121 (Figure 1-6). VC7203 GTX Transceiver Characterization Board www.xilinx.com Send Feedback UG957 (v1.3) October 17, 2014...
Page 14
J121.2 - 12V Blue J121.3 - NC Figure 1-6 shows the heatsink fan power connector J121. X-Ref Target - Figure 1-6 UG957_c1_06_100712 Figure 1-6: Heatsink Fan Power Connector J121 www.xilinx.com VC7203 GTX Transceiver Characterization Board Send Feedback UG957 (v1.3) October 17, 2014...
DIP Switches, page 17). Finally, a JTAG connector (J7) is available to provide access to the JTAG chain using one of the Xilinx configuration cables—Platform Cable USB, Platform Cable USB II, or Parallel Cable IV (PCIV). VC7203 GTX Transceiver Characterization Board www.xilinx.com...
SMA Connector Function Direction I/O Standard USER CLOCK_1_P Input LVDS_25 CLK_DIFF_1_P USER CLOCK_1_N Input LVDS_25 CLK_DIFF_1_N J100 USER CLOCK_2_P Input LVDS_25 CLK_DIFF_2_P USER CLOCK_2_N Input LVDS_25 CLK_DIFF_2_N J101 www.xilinx.com VC7203 GTX Transceiver Characterization Board Send Feedback UG957 (v1.3) October 17, 2014...
Six of the eight I/Os also map to 2 x 6 test header J125 providing external access for these pins (callout 26, Figure 1-2.). www.xilinx.com VC7203 GTX Transceiver Characterization Board Send Feedback UG957 (v1.3) October 17, 2014...
Table 1-12: User Pushbuttons FPGA (U1) Schematic Net Reference Name Designator Function Direction I/O Standard User Pushbutton Input LVCMOS18 USER_PB1 User Pushbutton Input LVCMOS18 USER_PB2 VC7203 GTX Transceiver Characterization Board www.xilinx.com Send Feedback UG957 (v1.3) October 17, 2014...
HDR-155805-01-BEYE cable assembly. Contact Samtec, Inc. for information about this or other cable assemblies. Figure 1-11 A shows the connector pad. Figure 1-11 B shows the connector pinout. www.xilinx.com VC7203 GTX Transceiver Characterization Board Send Feedback UG957 (v1.3) October 17, 2014...
Bidirectional differential serial data (P-side). GROUND Signal ground. The CP2103 supports an I/O voltage range of 1.8V to 3.3V. Xilinx UART IP is expected to be implemented in the FPGA fabric. The FPGA supports the USB-to-UART bridge using four signal pins: •...
1.25V reference, U45 (Texas Instruments P/N REF3012AIDBZT) • Pin 2-3 (AGND): In this configuration the VREFP on XADC is connected to analog ground and the ADC uses an on-chip reference. www.xilinx.com VC7203 GTX Transceiver Characterization Board Send Feedback UG957 (v1.3) October 17, 2014...
Appendix C Master Constraints File Listing The master Xilinx design constraints (XDC) file template for the VC7203 board provides for designs targeting the VC7203 Virtex®-7 FPGA GTX Transceiver Characterization Board. Net names in the listed constraints correlate with net names on the VC7203 board schematic.
For continual updates, add the Answer Record to your myAlerts. Solution Centers See the Xilinx Solution Centers for support on devices, software tools, and intellectual property at all stages of the design cycle. Topics include design assistance, advisories, and troubleshooting tips.
Page 74
14. 7 Series FPGAs GTX/GTH Transceivers User Guide (UG476) 15. 7 Series FPGAs Integrated Block for PCI Express v1.8 User Guide (PG054) 16. HW-CLK-101-SCLK2 SuperClock-2 Module User Guide (UG770) www.xilinx.com VC7203 GTX Transceiver Characterization Board Send Feedback UG957 (v1.3) October 17, 2014...
Safety IEC 60950-1:2005, Information technology equipment – Safety, Part 1: General requirements EN 60950-1:2006, Information technology equipment – Safety, Part 1: General requirements VC7203 GTX Transceiver Characterization Board www.xilinx.com Send Feedback UG957 (v1.3) October 17, 2014...
This product complies with Directive 2002/95/EC on the restriction of hazardous substances (RoHS) in electrical and electronic equipment. This product complies with CE Directives 2006/95/EC, Low Voltage Directive (LVD) and 2004/108/EC, Electromagnetic Compatibility (EMC) Directive. www.xilinx.com VC7203 GTX Transceiver Characterization Board Send Feedback UG957 (v1.3) October 17, 2014...