Table of Contents
Advertisement
2.
Engage the transmission bypass rods,
one on each side of the tractor, to move
the tractor manually without starting it.
Engage the bypass rods by pulling each
one back (a) and hooking it into the slot
(b) to lock it into place. See Figure 4-6.
NOTE: The tractor will not drive with the
bypass rods in the engage position.
3.
Disengage the bypass rods by reversing
steps (a) and (b) after moving the tractor.
See Figure 4-6.
Hydrostatic Transmission
Your zero turn tractor is equipped with dual
integrated hydrostatic pumps/transaxles that
are sealed and are maintenance-free. However,
this model is equipped with a transmission oil
expansion reservoir. Under normal operating
conditions, the oil level in the expansion
reservoir does not need to be checked and
no additional oil is needed. If checking the
reservoir oil level, proceed as follows:
WARNING! Check the oil level
ONLY before starting the tractor
when the transmission oil is fully
cooled.
1.
Clean the reservoir cap and the area
around the cap to prevent debris from
contaminating the transmission oil. See
Figure 4-7.
Figure 4-7
2.
Turn the reservoir cap counter-clockwise
to remove, then check the oil level in the
reservoir. Oil should be visible at the
bottom of the cup, but the oil level must
NOT be above the "FULL COLD" line. See
Figure 4-7. DO NOT FILL THE RESERVOIR.
3.
If necessary to add oil because of some
type of leakage, use a quality 20W50 motor
oil and add only enough oil to bring the
level to the "FULL COLD" line. Reinstall the
cap and fully tighten.
NOTE: Prior to the initial operation of the
tractor, the oil level in the reservoir may be
slightly higher than the maximum due to air
in the oil lines. Operation of the tractor will
eventually purge the air from the lines and
the oil level will settle to the maximum.
20
S
4— S
ection
ervice
Tractor Storage
If your tractor is not going to be operated
for an extended period of time (30 days to
approximately six months), the tractor should
be prepared for storage. Store the tractor in a
dry and protected location. If stored outside,
cover the tractor (including the tires) to protect
it from the elements. The procedures outlined
below should be performed whenever the
tractor is placed in storage.
1.
Change the engine oil and filter following
the instructions provided in the engine
manual packed with this manual.
WARNING! Never store the
tractor with fuel in the tank
indoors or in poorly ventilated
enclosures, where fuel fumes may
reach an open flame, spark or
pilot light as on a furnace, water
heater, clothes dryer, etc.
2.
If storing the tractor for 30 days or more:
a.
To prevent gum deposits from
forming inside the engine's
carburetor and causing possible
malfunction of the engine,
the fuel system must be either
completely emptied, or the
gasoline must be treated with a
stabilizer to prevent deterioration.
WARNING! Fuel left in the fuel
tank deteriorates and will cause
serious starting problems.
b.
Use a fuel stabilizer
between 30 and 90 days
•
Read the product
manufacturer's
instructions and
recommendations.
•
Add to clean, fresh
gasoline the correct
amount of stabilizer for the
capacity (approximately 3
gallons) of the fuel system.
•
Fill the fuel tank with
treated fuel and run the
engine for 2-3 minutes to
get stabilized fuel into the
carburetor.
c.
Emptying the fuel system for
storage of more than 90 days:
•
Prior to putting the tractor
in storage, monitor fuel
consumption with the
goal of running the fuel
tank empty.
•
Run the engine until it
begins to stall. Use the
choke to keep the engine
running until all fuel in
the carburetor has been
exhausted.
•
Referring to the engine
manual, drain the fuel
from the carburetor bowl.
3.
Clean the engine and the entire tractor
thoroughly.
4.
Fully charge the battery, then disconnect
the negative cable at the battery to
prevent possible discharge. Recharge
the battery periodically when in storage.
NOTE: Remove the battery if exposed
to prolonged periods of sub-freezing
temperatures. Store in a cool, dry location
where temperatures are above freezing.
5.
Lubricate all lubrication points.
NOTE: Using a pressure washer or garden
hose is not recommended for cleaning your
tractor. It may cause damage to electrical
components, spindles, pulleys, bearings or
the engine. The use of water will result in
shortened life and reduce serviceability.
Removing The Tractor From Storage
1.
Check the engine oil.
2.
Fully charge the battery and inflate the
tires to the recommended pressure.
3.
Fill the fuel tank with clean, fresh gasoline.
4.
Start the engine and allow to idle for
a few minutes to ensure engine is
operating properly.
5.
Drive the tractor without a load to
make certain all the tractor systems are
functioning properly.
Adjustments
for storage
:
Adjusting RH & LH Drive Control Levers
The RH and LH drive control levers can be
adjusted up or down and forward or backward
for the comfort of the operator. The drive
control levers can be placed in either of two
height positions, and/or can be moved forward
or rearward. Proper drive control lever and seat
adjustment will result in the following:
1.
In the neutral position with hands on the
control levers, the operator's upper arms
should be relaxed and approximately
vertical and their forearms should be
approximately horizontal.
2.
In the full forward position, the
operator's back should stay in contact
with the seat back and the control levers
should not contact operator's legs.
3.
In the full reverse position, the control
levers should not contact the operator's
legs or torso.
4.
Set the seat to the preferred operating
position. The adjustment lever is located
under the front edge of the seat. The
seat has 5" of front-to-rear adjustment
available.
5.
Check factory settings of control levers
for the conditions listed above.
NOTE: If control lever adjustments are
required, height adjustments should be
made prior to angular adjustments.
To adjust the drive control lever height, proceed
as follows:
WARNING! Shut the engine off,
remove the ignition key and
engage the parking brake before
making adjustments. Protect your
hands by using heavy gloves
when handling the blades.
Hide quick links:
Advertisement
Table of Contents
