Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for SuperLead 2200 Series
Summary of Contents for SuperLead 2200 Series
- Page 1 SuperLead 2200 Series 2D Imager Barcode Scanner User Guide V1.0...
-
Page 2: Table Of Contents
SuperLead Table of Contents Chapter 1 Factory Settings ........................ 3 1. Factory Settings ..........................3 Chapter 2 Communication Interface ....................4 RS-232 Serial Port Communication ..................4 Baud Rate Settings ......................4 Parity Bit Settings ......................4 USB Interface Communication ....................7 Serial Port Command Format .................... - Page 3 SuperLead Code 128（Open by Default） ..................16 Code 39（Open by Default） ..................16 Code 93（Close by Default） ..................17 Standard(IATA,Airline) 2 of 5(two-bar start/stop)（Close by Default） ......17 1.10 Industrial 2 of 5 (three-bar start/stop)（Close by Default）.......... 17 1.11 GS1 DataBar (RSS)（Close by Default） ................. 17 1.12 Telepen（Close by Default）...
-
Page 4: Chapter 1 Factory Settings
SuperLead Chapter 1 Factory Settings 1. Factory Settings Scanning the following barcode can restore the scanner to the factory defaults. Restore All Factory Defaults... -
Page 5: Chapter 2 Communication Interface
SuperLead Chapter 2 Communication Interfaces Superlead 2200 provides a TTL-232 interface and a USB interface to communicate with the host device. The host device can receive scanned data and send commands to control the engine or to access/alter the configuration information of the engine via the TTL-232 or USB interface. - Page 6 SuperLead...
- Page 7 SuperLead 4800 9600 19200 38400 57600 115200 1.2 Parity Check None,7,1 None,7,2 None,8,1 Even,7,1 Even,7,2 Even,8,1...
-
Page 8: Usb Interface Communication
SuperLead Odd,7,1 Odd,7,2 Odd,8,1 2. USB Interface Communication To connect USB cable, scanners can communicate through USB HID-KB and USB Virtual Serial Port. USB HID-KB Configuration Code USB Virtual Serial Port Configuration Code... - Page 9 SuperLead 3. Serial port command Format User Command Format： \x02\x11\x03XXXXXX. Serial Command Trigger Trigger push command: \x02P\x03 Trigger release command: \x02R\x03...
-
Page 10: Chapter 3 Common Function Settings
SuperLead Chapter 3 General Function Setting 1. Scanning Mode Settings Manual Mode：Through Key Trigger to scan code 2. Beeper-Good Read Switching Setting Open Good Read Beeper Close Good Read Beeper... -
Page 11: Led-Good Read Switching Settings
SuperLead 3. LED-Good Read Switching Setting Open Good Read LED Close Good Read LED 4. Barcode Scanning Delay After successfully scanning a barcode will delay to appointed time to decode next code, the default is 0ms Delay 0ms Delay 250ms... -
Page 12: Trigger Timeout Settings
SuperLead 5. Trigger Timeout Setting Button Trigger Timeout Setting，Default Timeout 30s 30s（Default）... -
Page 13: Chapter 4 Data Format Configuration
SuperLead Chapter 4 Data Format Setting 1. General Configuration Add remove some general configuration： Delete all add AddCRLF Add CR Add LF Add Tab Add Star(*) -
Page 14: Add Prefix
SuperLead 2. Add prefix Prefix Switch Barcode： Open Prefix Close Prefix Prefix Content Add： Making Barcode Format：^3+PREFIX+content required add+(.) Reference Barcode as follows： 3. Add Suffix Suffix Switching Barcode： Open Suffix Close Suffix... -
Page 15: Software Version Display
SuperLead Suffix Content Added： Making Barcode Format：^3+SUFFIX+content required add +(.) Reference Barcode as follows: 4. Display Scanner Serial Number Scan the following barcode to display scanner serial number: Display Serial Number 5. Display Software Version Number Scan the following barcode to display scanner software version number：... -
Page 16: Chapter5 Barcode Type
SuperLead Chapter5 Barcode Type 1. 1D Barcode Interleaved 2 of 5（Open by Default） Close Open China Post（Hong Kong） （Close by Default） Close Open Matrix 2 of 5（Close by default） Close Open... -
Page 17: Codabar（Open By Default
SuperLead Codabar（Open by default） Close Open MSI(Plessey)（Close by default） Close Open Code 128（Open by default） Close Open Code 39（Open by Default） Close Open... -
Page 18: Code 93（Close By Default
SuperLead Code 93（Close by Default） Close Open Standard(IATA,Airline) 2 of 5(two-bar start/stop)（Close by Default） Close Open 1.10 Industrial 2 of 5 (three-bar start/stop)（Close by default） Close Open 1.11 GS1 DataBar (RSS)（Close by default）... -
Page 19: Telepen（Close By Default
SuperLead Close Open 1.12 Telepen（Close by default） Close Open 1.13 Trioptic Code（Close by default） Clsoe Open 1.14 UPC-A/EAN13（Open by default） Close Open... -
Page 20: Code 11（Close By Default
SuperLead 1.15 Code 11（Close by default） Close Open 2. 2D Barcode QR（Open by default） Close Open Data Matrix（Open by default） Close Open PDF417（Open by Default）... - Page 21 SuperLead Close Open...
-
Page 22: Aztec（Close By Default
SuperLead Aztec（Close by default） Close Open Hanxin（Close by default） Close Open...
Need help?
Do you have a question about the 2200 Series and is the answer not in the manual?
Questions and answers