Summary of Contents for Team Losi Desert Buggy XL-E 2.0
Page 1
INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’UTILISATION Before operating this vehicle, please read all printed materials thoroughly. MANUALE DI ISTRUZIONI Horizon Hobby is not responsible for inadvertent errors in this manual.
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com or www.towerhobbies.com and click on the support or resources tab for this product. MEANING OF SPECIAL LANGUAGE The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superfi...
INSTALLING THE BATTERIES 1. Remove the 2 body clips from the vehicle as shown. 2. Lift the body to access the chassis. 3. Install (2) fully charged batteries in the vehicle. 4. Secure with the hook and loop straps. 5. Connect the batteries to the ESC. IMPORTANT: Secure the ESC wires so they do not interfere with the gearing.
BINDING AND CALIBRATING THE RECEIVER Binding is the process of linking the SR6100AT receiver to your Spektrum transmitter. The AVC CAUTION: When the bind process is complete, the throttle and steering channels are features on the receiver can be enabled or disabled during the binding process. active.
Place the vehicle on a stand supporting the chassis so the wheels are off the ground during CONTROL DIRECTION TEST the steering and throttle tests. Verify all the controls work correctly before turning it on with the wheels on the ground. STEERING THROTTLE Move the steering wheel Left and Right and observe the direction the front wheels...
VEHICLE TUNING This Vehicle Tuning Guide will take you through the basic tuning adjustments and will describe the changes to the handling of your vehicle. Before making any setup changes, make sure all suspension parts move freely and that there are no broken or dislodged parts. Only make one change at a time to clearly feel the impact of that change.
DROOP Always measure the droop (down travel) with the shocks on the vehicle. Droop is measured from the center of the top shock mount to the center of the bottom shock screw. More front and rear droop will accelerate better in bumps when going straight, but can cause the vehicle to traction roll in rough turns. Less front and rear droop will slide over bumps better in turns and may be better on high-speed and high-traction tracks.
FRONT TOE Never run front toe-in which can cause limited steeering response. FACTORY SETTING Toe-Out 33mm Front Toe Characteristics Toe-out (shorter steering rods) increases steering response when entering the turn and straight line stability; however, it will Toe-Out decrease on-power steering SWAY BARS The vehicle is equipped with medium (4mm) sway bars on the front and rear.
SPEKTRUM FIRMA 780KV BRUSHLESS MOTOR ™ ™ PRECAUTIONS SETTING THE GEAR MESH • Never touch moving parts. The gear mesh has already been set at the factory. Setting it is only necessary when changing motors or gears. • Never disassemble while the batteries are installed. Proper gear mesh (how gear teeth meet) is important to the performance of the vehicle.
Page 11
ESC FUNCTIONS AND MODES The ESC includes programming options so you can adjust the way your vehicle performs. Refer to the included programming table to adjust the ESC for your driving conditions. PROGRAMMING TABLE Default Settings PROGRAMMING VALUE PROGRAMMING ITEMS 1.
VEHICLE MAINTENANCE The following items require semi-frequent maintenance. Always clean screw threads and apply removeable thread locking compound when threading machine screws into metal parts. SHOCK DISASSEMBLY/CLEANING Remove the shocks and service as needed. Replace worn parts. FRONT REAR Pull the spring up and away from the lower cup. Slide the lower spring cup up and off of the shaft.
REFILLING/BLEEDING SHOCKS Fill the shock body 5mm (0.2 in) from the top with 40wt silicone shock oil (TLR74025). Slowly move the piston up and down 5 times, allowing air to rise to the top. Let the shock sit for 5 minutes. With the piston all the way down, fi...
REAR DIFFERENTIAL Remove the rear clip. Remove the cover and differential. Check the differential fl uid and refi ll or replace as needed with DYN2656 (30,000CS) fl uid. The fl uid level should be about 0.12 in (3.0mm) from the top surface of the case.
CENTER DIFFERENTIAL Inspect the spur gear. Replace if worn or damaged. Check the differential fl uid and refi ll or replace as needed with DYN2657 (50,000CS) fl uid. The fl uid level should be about 0.12 in (3.0mm) from the top surface of the case. Do not overfi...
TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE SOLUTION Battery not charged or plugged in Charge battery/plug in Vehicle does not operate ESC switch not "On" Turn on ESC switch Transmitter not "On" or low battery Turn on/replace batteries Pinion not meshing with spur gear Adjust pinion/spur mesh Pinion spinning on motor shaft Tighten pinion gear setscrew on motor shaft fl...
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a These terms are governed by Illinois law (without regard to confl ict of law principals). This Li-Po battery, please contact the appropriate Horizon Product Support offi ce. warranty gives you specifi...
HARDWARE VISSERIE ET ACCESSOIRES ZUBEHÖR VITI E PARTI ACCESSORI M3 x 10mm (LOS255005) 3 x 8mm (LOS255002) M3 x 22mm (LOS255001) M5 x 20mm (LOS255002) M5 x 30mm (LOS255001) M4 x 12mm (LOS255002) M4 x 20mm (LOS255002) M5 x 35mm (LOS255001) M5 x 18mm (LOS255002) M5 x 20mm (LOS255002) M5 x 45mm (LOS255001)
Page 19
10.1 x 14 x .25mm (LOS256001) 8 x 19 x 6mm (LOS257000) 4 x 10 x 1mm (LOS256001) 10 x 22 x 6mm (LOS257001) M4 (LOS256000) 12 x 24 x 6mm (LOSB5972) M5 (LOS256000) M5 (LOS256000) 7 x 10 x 4mm (LOS257002) 8 x 22 x 0.2mm (LOS256001) (LOS256005) (LOS256005)
REPLACEMENT PARTS // TEILELISTE // LISTE DES PIÈCES DE RECHANGE // ELENCO DEI RICAMBI Part # English Deutsch Français Italiano LOS250019 LED Light Bar Set:DBXL-E LED-Leuchtbalken-Set: DBXL-E Ensemble de rampe d’éclairage à DEL : DBXL-E Set barra a LED: DBXL-E LOS250020 Roll Cage Screw Set: DBXL-E Überrollkäfi...
REPLACEMENT PARTS // TEILELISTE // LISTE DES PIÈCES DE RECHANGE // ELENCO DEI RICAMBI Part # English Deutsch Français Italiano LOS255000 Set Screw, Set,(20):1:5 4wd DB XL Schraubensatz (20): 1:5 4wd DB XL Vis de fi xation, ensemble (20) : 1:5 4rm DB XL Set viti (20): 1:5 4WD DB XL Vis d’assemblage creuses, ensemble (30) : Set di viti a testa cilindrica (30): 1:5 LOS255001...
OPTIONAL PARTS // OPTIONALE TEILE // PIÈCES OPTIONNELLES // PARTI OPZIONALI Part # English Deutsch Français Italiano Karosseriesatz mit Stickerbogen, transparent Ensemble carrosserie avec feuille d’autocol- Carrozzeria con adesivi, trasparente: LOS250018 Body Set W/Sticker Sheet, Clear: DBXL-E DBXL-E lants, transparent : DBXL-E DBXL-E Engrenage à...
Need help?
Do you have a question about the Desert Buggy XL-E 2.0 and is the answer not in the manual?
Questions and answers