Table of Contents
Advertisement
Your pool is designed for years of pleasurable, safe
family fun. But when used incorrectly, a swimming pool
can be dangerous. To insure your pool is used safely,
you MUST observe the following safety precautions:
- Do not dive!- Do not jump!-No rough play!- no
running or pushing.
- Do not walk on the top rail. It can be slippery & is not
a walkway.
- Be sure to install all safety labels provided with your
pool according to the instructions.
- Keep a safety rope 1/4" by 50' with a floatation buoy
with an outside diameter of 15". Have accessible in
prominent area by your pool.
- Post near all entrances to the pool area a list of
phone numbers of the:
• Nearest available police
• Nearest available fire department
• Nearest available rescue unit
• 911 emergency number if available
• Nearest ambulance service
• Nearest available hospital
• Nearest available physician
- Provide fencing or enclosure, which is independent of
the house as a closure around the entire pool area.
The fence must be made of durable material to make
pool inaccessible to toddlers and uninvited guests.
- Make sure gate is always closed, Be sure to follow
local building code requirements for load capacity and
fencing.
The safety stickers must be installed as per following instructions. Failure to
properly install warning labels will void warranty. Failure to mount these safety
labels may subject you to substantial liability in case of injury.
WARNING
IMPORTANT NOTICE!
READ BEFORE INSTALLATION
1
CREATION/GENESIS
!
- Check with your local town for any special laws in
your locale.
- Never drink alcoholic beverages or use any
intoxicants, which could hinder your judgment or
reflexes.
- Never use pool alone. All children must be
supervised continuously.
- Do not use pool if bottom is not clearly visible: At
night sufficient lighting must be available. It is the
pool owner's sole responsibility to provide adequate
lighting for pool bottom, safety signs and walkways,
which exceed the standards of the EIS of North
America.
- Do not climb, stand or sit on any pool structure or
the filter system. Components such as the filtration
system, pumps, and heater must be positioned so as
to prevent their being used as a means of access to
the pool by young children.
- Be sure that all toys, chairs and tables or similar
objects that a young child could climb on are at least
4 feet away from pool.
- Do not use pool during electrical or rain storms
- See available National Spa and Pool Institute
(NSPI), publications for more tips on pool safety.
1
Advertisement
Table of Contents
Related Manuals for Aqua Leader CREATION
Summary of Contents for Aqua Leader CREATION
- Page 1 CREATION/GENESIS WARNING Safety Information Your pool is designed for years of pleasurable, safe - Check with your local town for any special laws in family fun. But when used incorrectly, a swimming pool your locale. can be dangerous. To insure your pool is used safely,...
- Page 2 WARNING Safety Information Notice to Pool Owners and Installers These warnings are not to be removed under any circumstances! If they fall off or become discolored please request replacements, which will be sent at no charge. Practical pool safety- These labels and your cooperation may save a life! In addition, failure to mount these instructions may subject you to substantial liability in case of injury.
- Page 3 Above ground pools are not designed to be installed below the surface. Outside ground forces can collapse the pool wall. If you hire a professional installer, this installation booklet must be followed. AQUA LEADER INC. will not be responsible for improper installation.
- Page 4 ATTENTION! Aqua Leader is not responsible for any damages to your pool if it is not installed according to the installation instructions. Installing your pool on soft or non-leveled ground will void the warranty.
- Page 5 1.2.5: Retrace the pool circle. NOTE 1: Do not remove the steel rod at the center of the pool. Aqua Leader NOTE 2: is not responsible for any damages to your pool if it is not installed according...
- Page 6 STEP 2: Bottom wall channel and bottom plate 2.1: Place the bottom wall channels and bottom plates in a circle. NOTE: During installation, the curves and length of the bottom wall channels will help to position the bottom plates. 2.2 : Install the round bottom wall channel into the bottom plate.
- Page 7 STEP 3: WALL INSTALLATION Measure 3.1: Before installing the wall, use a flexible tape measure to measure the perimeter of the wall. Measure by inserting the tape measure into the bottom wall channels around the pool and compare it with the table PART LIST in the ANNEX under the name Steel wall (Hole-to-Hole).
- Page 8 3.4: With the assistance of at least 3 people, unroll the wall so that the painted pattern faces the outside of the pool and that the pre-punched opening for the skimmer is on the top. 3.5: Guide the wall in the bottom wall channels until both ends meet.
- Page 9 3.8: Install the bolts and nuts into each hole (the quantity of screws corresponds to the amount of holes). All holes of the aluminum bars must be filled IMPORTANT! 3.9: Make sure that the bolt heads are on the interior side of the pool. IMPORTANT REMINDER! Due to the enormous pressure exerted against the pool wall, it is essential to screw in all bolts tightly.
- Page 10 3.10: Verification At this stage, it is very important to take measures after the installation of the wall as the parameters are likely to have changed. 3.11: Attach a rope to the steel rod in the middle of the pool. 3.12: Pull the rope to the wall keeping the rope under tension, measuring the curve from one side of the pool to the other side.
- Page 11 Step 4: Support post installation 4.1: Slide the base of the support post into the front part of the bottom plate. 4.2: Secure the support post with a 1½” screw in the opening at the base of the post. 4.3: Insert the base cover at the bottom of the post.
- Page 12 5.1.1 – B2: Cut the felt along the base of the wall. Cove NOTE: The cove is necessary to prevent the liner from creeping underneath the wall. Aqua Leader will decline any liability for damages if this step is omitted. Use only humid screened soil. Do not use thin sand, grass, turf or any product identified as “pool base”...
- Page 13 Sand cove 5.1.2 - A: Make sure that the cove is at least 3 inches high along the wall and ends in a gentle slope towards the interior of the pool. Be sure to compact the sand and remove any small stones.
- Page 14 5.2.2 - A2: Bead liner Hang the bead of the liner at the top of the wall. As the bead is installed, place the top wall channel and ensure that the channels are centered in the middle of the posts. “Snap-In”...
- Page 15 Step 5.2.2 - B: Overlapping liners installation If you don’t have this type of liner, jump to the previous section! 5.2.2 - B1: Remove the top wall channels one section at a time. 5.2.2 - B2: Overlap the liner at the top of the wall and hold it in place by inserting the plastic coping.
- Page 16 5.2.2 - B5: Proceed for the rest of the wall. NOTE 1 : Do not install the liner on both sides simultaneously. Be careful not to create wrinkles. Install the liner from one point to the end by following one direction. Liner adjustment and filling the pool 5.2.3: To ease the installation of the liner, you can use a vacuum cleaner by blocking the skimmer with adhesive tape.
- Page 17 5.2.9: Continue filling the pool until the cove is completely covered. For overlap liners: While filling the pool, gently pull up the excess liner to the top of the pool wall just along the cove area. Set the liner firmly into the top wall channels. IMPORTANT REMINDER!! Pull the liner firmly but gently.
- Page 18 STEP 6: TOP SEAT AND SEAT CAP INSTALLATION UPRIGHT CLIP 6.1: Place the top of the support post on the wall and insert the upright clips. The upright clips snap onto the top of the post by applying a simple pressure thus securing the wall and the post together.
- Page 19 SEAT CAP INSTALLATION 6.6: Hook the rear (large part) seat covers under the edge of the seat (interior side of the pool). Once the rear is secured, push the front part forward. 6.7: Insert the locking tab under the front part of the seat cap and push firmly.
- Page 20 In addition, wax application on the surface will assure you to keep the shinny appearance and prevent dirt to stick on the surface. Some cleaning products can be used to clean watermarks. Check with your AQUA LEADER dealer.
- Page 21 WINTERIZING YOUR POOL All of our liners are designed to be left up all winter, but nonetheless are subject to the warranty of the liner being purchased. Continue to chlorinate and filter your water until the pool is closed down. Before closing down your pool for the winter, you must make a complete inspection of the pool.
- Page 22 RULES FOR SAFE POOL USE You have purchased a family pool of superior quality and durability. Your Aqua Leader warranty guarantees you years of enjoyment under normal use and care. (See warranty for complete details and conditions.) As an owner, you are responsible for the protection of those who swim in your pool.
- Page 23 ANNEX - PARTS LIST – GENESIS / CREATION Description Part number 12’ 15’ 18’ 21’ 24’ 27’ 30’ A- Top wall channels 12’ 10715XX160000 15’ 10718XX160000 21’ 10721XX160000 24’ 10724XX160000 27’ 10727XX160000 30’ 10730XX160000 B- Bottom wall channels 12’ 10815XX000000 15’...
- Page 24 Manufactured by Trendium Pool Products Inc.,(member of the Wilbar Group) 7050 St-Patrick Street, LaSalle, Quebec H8N 1V2 CANADA. Aqua Leader is a brand of the Wilbar Group. The dimensions, weights, illustrations and other specifications are approximate. The company reserves the right to modify and/or discontinue without notification any feature in any pool model.
Need help?
Do you have a question about the CREATION and is the answer not in the manual?
Questions and answers