Table of Contents
Advertisement
Quick Links
The INT-SCR-BL multifunctional keypad with proximity card
reader can operate as:
partition keypad – a device supported by the CA-64 alarm
control panel, as well as INTEGRA control panels with
any firmware version, and identified as INT-S/SK. It is
designed to control arming of one partition. The device
makes it possible to execute the functions of access
control and electromagnetic door lock operation.
It enables changing the user code and calling the control
functions for outdoor devices, and identifies users by
their access code.
partition keypad with proximity card reader – a device
supported by the INTEGRA control panels with firmware
version 1.05 or later and identified as INT-SCR.
It performs identical functions as the partition keypad,
but allows the users to use proximity cards.
entry keypad – a device supported by the INTEGRA
control panels with firmware version 1.05 or later and
identified as INT-ENT. The main task of the entry
keypad is activation of the delay in the partition for the
zones with reaction type
period during which these zones will act as delayed
ones is programmable for the keypad. After expiry of the
programmed time, the interior delayed zones again act
as instant ones, unless the partition is disarmed.
Design of the keypad enables it to be installed outdoors.
The device is additionally equipped with a bell button to
control the OC type low-current output. Press the button to
short the output to the common ground.
This manual applies to the module with electronics version
1.4 and firmware version 2.01 (or later).
1. Description of the Keypad
The partition keypad has 13 keys with permanent or
temporary (automatically activated) mode backlit and LED
indicators:
-
(red color),
ALARM
-
(green color),
ARMED
-
(yellow color).
TROUBLE
Information conveyed by means of the LED indicators depends on the keypad operating mode.
Alternative blinking of all the LEDs (from the left to the right) indicates lack of communication between
the keypad and the control panel. This situation may take place when the STARTER program is
running in the control panel, or when the cable connecting the keypad and the control panel is
damaged.
MULTIFUNCTIONAL KEYPAD
WITH PROXIMITY CARD READER
®
3. I
NTERIOR DELAYED
INT-SCR-BL
. The time
Fig. 1. INT-SCR-BL multifunctional
int-scr_en 06/12
keypad.
Advertisement
Table of Contents
Related Manuals for Satel INT-SCR-BL
Summary of Contents for Satel INT-SCR-BL
- Page 1 WITH PROXIMITY CARD READER ® INT-SCR-BL int-scr_en 06/12 The INT-SCR-BL multifunctional keypad with proximity card reader can operate as: partition keypad – a device supported by the CA-64 alarm control panel, as well as INTEGRA control panels with any firmware version, and identified as INT-S/SK. It is designed to control arming of one partition.
- Page 2 SATEL INT-SCR-BL Cable color Function power supply input (+12 V) blue ground (COM) green data (DTA) black clock (CLK) yellow relay NO contact (normally isolated from the relay common contact) pink relay NC contact (normally shorted to the relay common contact)
- Page 3 INT-SCR-BL SATEL 4. Turn on the keypad supply. The keypad will generate 4 short beeps and 1 long beep, and the LEDs designated ] and ] will start blinking alternately (the ends of green ALARM ARMED and black cables can then be separated).
- Page 4 SATEL INT-SCR-BL 5. Operation in the Partition Keypad Mode The LEDs show following information: (red color) – steady light indicates an alarm in the keypad controlled partition, while ALARM blinking indicates that an alarm was triggered in the partitio n (alarm memory). The LED goes off when alarm is cleared.
- Page 5 INT-SCR-BL SATEL Authorization control [Unauth. event] – opening the door without entering a password from the keypad (e.g. with the key) will generate an „Unauthorized door opening” event, it can also be signaled on the output type 93 NAUTHORIZED ACCESS arm on unauth.
- Page 6 SATEL INT-SCR-BL authorized to disarm the partition). The zones of the blocked partition will not trigger the burglary alarm. The blocking duration is defined individually for each user using the EMPORARY code type and for the partition ( PARTITION BLOCKING LOCKED FOR GUARD ROUND Guard round control –...
- Page 7 INT-SCR-BL SATEL 6. Operation in the Mode of Partition Keypad with Proximity Card Reader Information conveyed by the keypad with LED indicators in this mode is identical to that in the partition keypad mode. Additionally, all LEDs of the partition keypad with reader blinking simultaneously indicate waiting for the card read-in (during the procedure of adding a card to the user).
-
Page 8: Specifications
Operating temperature range ....................-25...+55 °C Maximum humidity........................93±3% Dimensions........................47 x 158 x 24 mm Cable length ............................4 m Weight .............................297 g The declaration of conformity may be consulted at www.satel.eu/ce SATEL sp. z o.o. ul. Schuberta 79 80-172 Gdańsk POLAND tel.
Need help?
Do you have a question about the INT-SCR-BL and is the answer not in the manual?
Questions and answers