Sealey BG150BS Manual

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear a face
instruction shield
manual
1. saFetY

electrical saFetY

1.1.
warning! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
1.1.1. electrical safety information, it is important that the following information is read and understood.
1.1.2. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.3. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
8
correct fuse - see fuse rating in these instructions.
dO nOt pull or carry the appliance by the power cable.
8
dO nOt pull the plug from the socket by the cable.
8
dO nOt use worn or damaged cables, plugs or connectors.
8
1.1.4. Ensure that any faulty item is repaired or is replaced immediately by a qualified electrician.
1.1.5. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.

general saFetY

disconnect the grinder from the mains power before changing accessories, servicing or performing any maintenance.
9
maintain grinder and stone in good condition. Check moving parts and alignment. If necessary use an authorised service agent.
9
Replace or repair damaged parts. Use genuine parts only. Unapproved parts may be dangerous and will invalidate the warranty.
warning! Always work with the grinder safety guard in place.
‰
The grinding wheel or stone must only be changed by persons holding an appropriate grinding wheel certificate.
9
Wear approved safety goggles, ear defenders and appropriate dust mask if grinder generates dust.
9
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain long hair.
9
Use grinder in a suitable work area, keep area clean, tidy and free from unrelated materials, and ensure adequate lighting.
9
maintain correct balance and footing. dO nOt over-reach and ensure the floor is not slippery. Wear non slip shoes.
9
Use only approved grinding stones, and only use the normal grinding surface.
9
Check grinding stones to ensure they are not split, cracked or damaged in anyway. See chapter 5. If in doubt dO nOt use the stone.
9
Grinding stones must be securely attached before use, but not over tightened.
9
Keep non essential persons away from the working area, use screens if necessary.
9
dO nOt operate the grinder if any parts are missing or the grinder is damaged.
8
dO nOt use the grinder for a task it was not designed to perform.
8
dO nOt operate grinder where there are flammable liquids or gasses.
8
warning! dO nOt grind any materials containing asbestos.
‰
dO nOt get the grinder wet or use in damp or wet locations.
8
dO nOt switch the grinder on whilst the stone is in contact with the workpiece.
8
dO nOt cover the grinder air vents. To do so will overheat the machine.
8
dO nOt touch the workpiece immediately after grinding as it will be very hot.
8
dO nOt try to cool the grinding stones with water or other lubricants.
8
dO nOt touch the grinding disc whilst operating, or whilst plugged into the mains power.
8
dO nOt leave the grinder running unattended.
8
dO nOt operate the grinder when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
© Jack Sealey limited
bench grinder Ø150mm with 50mm belt
sander & light 250w/230v
model no:
Wear protective
clothing
Original Language Version
bg150bs
recommended
fuse rating
3 amp
BG150BS | Issue:2 (H,F) 10/07/18