Related Manuals for HazeBase base-prime
Summary of Contents for HazeBase base-prime
- Page 1 Stargarder Straße 2 30900 Wedemark Germany Phone: + 49-5130-37 10 05 Fax: + 49-5130-37 10 06 E-Mail: info@hazebase.com contact www.hazebase.com...
-
Page 2: Table Of Contents
7. Device information ..........................14 8. Reset factory settings ........................... 14 9. pump characteristics ..........................15 10. More Settings ............................16 11. Scope of Delivery ..........................17 12. Technical specifications ........................17 13. Warranty conditions ........................... 18 14. Contact ..............................19 www.hazebase.com... -
Page 3: Introduction
• Spilled fluid or splashed fluid droplets can cause slip hazard. Mop up the fluid and dispose of it according to regulations. hazebase fog liquid is an enviromentally safe product and it can be recycled biologically. Artificially-made fog can be produced in many different ways. The method used here to produce fog, with a device which works according to the vaporizer principle, is the most harmless one. -
Page 4: Commissioning Of Base•Prime
80% 3.2 Devicelabeling A) Nozzle for fog emission B) RJ45 Ethernet socket for Artnet and sACN C) 5 pin XLR DMX input and output (DMX512) D) 3-pin XLR analog input E) PowerCon power connection F) Touchscreen for operating www.hazebase.com... -
Page 5: First Steps
30%. In the screen „Pump Adjustment“ instead of „p%“ „max. 30% „is displayed. This is to indicate that the adjust- ment is given only for the small pump. The small pump is only used in the 1-30% percentage range. www.hazebase.com... -
Page 6: Operation Of Base•Prime
3. Analog (Chapter 4.4) 4. Manual Operation (Chapter 4.2) After switching on the base•prime, the hazebase logo appears on the display (F). The following figure shows the main menu of the base•prime. L) Analog Input Display: Shows the selected mode P) Ethernet display: Indicates which protocol was and current voltage. -
Page 7: Manual Mode
It is important to know that the pump characteristics can influence the ejected amount of fog. This also means that at selected 100% possibly less fog can be generated. Further information can be found in the chapter pump characteristics www.hazebase.com... -
Page 8: Operation Via Dmx
It is important to know that the pump characteristics can influence the ejected amount of mist. This also means that at selected 100% possibly less fog can be generated. Further information can be found in the chapter pump characteristics www.hazebase.com... -
Page 9: Operation Via Analog
With BACK you can return to the main menu without saving or to SETTINGS with ANALOG SAVE is saved and back. If the base•prime is activated in latched mode, it must first be deactivated in latched mode. Switching is possible, but the machine can not be deactivated. www.hazebase.com... -
Page 10: Betrieb Über Ethernet
In both cases, make sure that the base • prime has configured a valid network address and subnet mask. You can check this under SETTINGS-> IP-CONFIG and adjust if necessary. A detailed description follows on page 12. www.hazebase.com... -
Page 11: Operation Via Timer
Also, use the AUTO START setting if you want to turn on the timer immediately after the operating temperature has been reached. To manually start and stop the timer, press the ACTIVE or INACTIVE button. All set values are stored with the TIMER SAVE button. www.hazebase.com... -
Page 12: Setting Up Ip Address
For networks where the IP address and subnet mask are to be used according to the ARTNET standard, first set the mode to STATIC and then press ARTNET. The IP address is then formed from the fixed MAC address of the device and an OEM code. The subnet mask is set to 255.0.0.0. www.hazebase.com... -
Page 13: Adjust The Screen Brightness
SETTINGS -> NEXT -> SETTINGS 2 -> SCREENSAVER Here you can set the duration of the screensaver. Press + or - to change the value. With SAVE they save their attitude. BACK will take you to the previous screen without saving settings. www.hazebase.com... -
Page 14: Device Information
Here an additional program, a computer and an existing network connection between PC and de- vice is needed. Please refer to the Hazebase website for new firmware versions and procedures. BACK will take you to the previous screen without saving settings. -
Page 15: Pump Characteristics
The machi- nes are not exactly the same in terms of production output. Furthermore, aging processes can influence the output quantity. With this adjustment method you can compensate for the differences. www.hazebase.com... -
Page 16: More Settings
With Back you can cancel the process, with STANDBY you can switch directly to standby mode. In case of an error E-1, E-2 or E-4 or a combination of these, the following screen appears with more or less error messages: www.hazebase.com... -
Page 17: Scope Of Delivery
DMX, Art-Net, sACN, analog (0-10V), manual, timer operation Weight: 16.5 kg (35 lbs) Fog duration Fog Value Impulse-Mode Extended-Mode 100% 128s 112s 176s 167s 347s 378s The measurements were carried out with base * M. For other fluids, the fogging times may be different. www.hazebase.com... -
Page 18: Warranty Conditions
The right of guarantee service is also lost if fluids other than Original hazebase fluids have been used or if units are sent to us with full fluid bottles. -
Page 19: Contact
English 14. Contact hazebase Founder Uta Raabe Stargarder Straße 2 30900 Wedemark GERMANY Tel: +49 (0) 5130-371005 Fax: +49 (0) 5130-371006 info@hazebase.com www.hazebase.com www.hazebase.com...
Need help?
Do you have a question about the base-prime and is the answer not in the manual?
Questions and answers