Sealey LP290 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. PLUG & MAINS POWER SUPPLY.
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also
recommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are
plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual
Current Device by contacting your Sealey dealer.
YOU MUST also read and understand the following instructions concerning electrical safety.
NOTE: 110 volt heaters are usually operated by connecting to a transformer or a generator. Check to ensure all supply equipment is compatible
with the rating of the heater.
1.1.1. The Electricity at Work Act 1989 requires all portable electrical appliances, if used on business
premises, to be tested by a qualified electrician, using a Portable Appliance Tester (PAT), at least
once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for
the safe condition of those appliances and the safety of the appliance operators. If in any doubt
about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the
power supply. See 1.1.1 and 1.1.2 and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all connections
to ensure that none are loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply to be
used and that the plug is fitted with the correct fuse - see fuse rating on right.
1.1.7. Important: For use with a 110 volt supply - ensure that the 110 volt transformer or generator
is adequately rated.
1.1.8. DO NOT pull or carry the appliance by the power cable.
1.1.9. DO NOT pull the plug from the socket by the cable.
1.1.10. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired
or replaced by a qualified electrician. When an ASTA/BS approved UK 3 pin 13 amp plug or 110 volt
plug is damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only - see diagrams on right).
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and that
the restraint is tight.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance plugged
into it will be protected. The cable core section is important and should be at least 1.5mm
the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of 2.5mm
section cable.
1.2. GENERAL SAFETY.
 WARNING! Disconnect heater from mains supply before servicing or performing maintenance. Replace or repair damaged parts. Use genuine
parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
 WARNING! NOT to be used for the heating of habitable areas of domestic premises: for use in public buildings, refer to national regulations.
Store gas cylinders in accordance with regulations applicable to such appliances.

Ensure that nothing stands or passes in front of the heater. Mandatory minimum distance from the heater is 1 metre.

Use the supplied pressure regulator only.

Ensure continuous ventilation is provided to the heater operating area. A ventilation opening must run to the outside of the premises where the heater is

to be operated. The opening must be 100cm
 WARNING! If the heater is used for prolonged periods at maximum power, ice may form on the propane cylinder. This is due to excessive
evaporation. In such a case DO NOT use the heater to de-ice the cylinder.
DO NOT use the heater if damaged. Take immediate action to repair or replace damaged parts. Use an authorised service agent only.

DO NOT allow untrained persons to ignite the heater.

DO NOT operate the heater without the cover.

DO NOT exceed the 100W/m

DO NOT use a naked flame to try and ignite the heater.

DO NOT use the heater near inflammable, combustable or explosive materials - liquids, solids or gases.

DO NOT leave the heater unattended whilst in use.

DO NOT obstruct the air inlet and outlet sections of the heater. Keep immediate area clean and tidy.

DO NOT point the heater towards the gas cylinder.

Keep the heater clean and in good working order.

Ensure that the heater is correctly turned off and the gas source isolated, when not in use.

When not in use for any length of time, store heater in a safe, dry, childproof location.

© Jack Sealey Limited
INSTRUCTIONS FOR:
SPACE WARMER PROPANE HEATER
139,727-289,384BTU/HR 110/230V
MODEL NO:
2 for every kW and must also be set at an equal distance from the upper and lower parts of the heater operating area.
3 limit considering the volume of the empty operating location.
Original Language Version
LP290
2 , but to be absolutely sure that the capacity of
Recommended Fuse Rating: 13Amp
110V
Brown
Blue Neutral
Live
Connection
Connection
Yellow &
Cable
Green
Restraint
Earth Wire
Connection
LP290, Issue No: 2(I) - 24/09/14
230V
2