Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Samson CONCERT 88X
Summary of Contents for Samson CONCERT 88X
- Page 1 Frequency Agile Wireless System OWNER'S MANUAL...
- Page 2 Copyright 2019, Samson Technologies Corp. Samson Technologies Corp. 278-B Duffy Ave Hicksville, NY 11801 www.samsontech.com...
-
Page 3: Important Safety Information
For Countries not mentioned above, please contact your local authorities for a correct method of disposal. By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health. Concert 88x Wireless System... - Page 4 Important Safety Information 13. Unplug the apparatus during lightening Read these instructions. storms, or when unused for long periods Keep these instructions. of time. Heed all warnings. 14. Refer all servicing to qualified personnel. Follow all instructions. Service is required when the apparatus has been damaged in any way, such Do not use this apparatus near water.
- Page 5 Important Safety Information FCC Rules and Regulations Samson wireless receivers are certified under FCC Rules part 15 and transmitters are certified under FCC Rules part 74. Licensing of Samson equipment is the user’s responsibility and licensability depends on the user’s classification, application and frequency selected.
- Page 6 For travel or permanent installation, the Concert 88x includes a standard 19" rackmount kit. In these pages, you’ll find a detailed description of the features of the Concert 88x wireless system, as well as a guided tour through its control panel, step-by-step instructions for its setup and use, and full specifications.
- Page 7 Press and hold the button for more than 10 seconds to enter IR set mode, the display will flash slowly. This will send the receiver’s current selected channel to the transmitter. POWER Switch - Use this to turn the CR88x power on and off. Concert 88x Wireless System...
- Page 8 CR88x Receiver Features - Rear Panel DC Input - Connect the supplied power adapter here, using the strain relief as shown in the illustration below. WARNING: Do not substitute any other kind of power adapter. Doing so can cause severe damage to the CR88x and will void your warranty. BALANCED OUTPUT - Use this electronically balanced low impedance (600 Ohm) XLR jack when connecting the CR88x to professional (+4dBu) audio equipment.
- Page 9 Belt Clip - Use this clip to fasten the CB88 transmitter to a belt or guitar strap. Battery Cover Release - Push in both sides and pull back to open the CB88 battery cover. Antenna - This permanently attached transmitter antenna should be fully extended during normal operation. Concert 88x Wireless System...
- Page 10 CB88 Beltpack Transmitter - Features Input GAIN Control - This control adjusts the transmitter input sensitivity to work with microphone and instruments inputs. For optimal performance, using the included screwdriver, set the input GAIN control to where you see the CR88x PEAK indicator start to light under high levels, then turn down slowly until the PEAK light stops lighting.
- Page 11 IR SET to channelize the transmitter. The battery cover must be open and the IR Lens facing towards the receiver to load the selected channel. Screwdriver - Designed for use in adjusting the CH88 input GAIN control. Concert 88x Wireless System...
-
Page 12: Quick Start - Single System Setup
In order for your wireless system to work correctly, both the receiver and transmitter must be set to the same channel. Follow this basic procedure for setting up and using your Concert 88x wireless system: Physically place the CR88x receiver where it will be used, and extend the antennas vertically. - Page 13 IR window facing the IR transmitter on the front panel of the CR88x receiver. 5. Plug receiver into audio system 6. Press Select button to change channel 7. Install batteries 8. Turn on belt pack transmitter Concert 88x Wireless System...
-
Page 14: Multiple System Setup
Quick Start - Single System Setup When the transmission is complete, the CR88x will receive RF signal and the tone key from the transmitter. The READY indicator will light on the front panel of the CR88x receiver. Turn on your connected amplifier or mixer, but keep the volume all the way down. -
Page 15: Rack Mounting
In order to mount two CR88x receivers in one rack space, the system includes a center connection piece. Slide the center connection piece into the groove of each receiver and attach the short rack ears to each receiver. Mount the receivers into the rack using the crisscross pattern described above. Concert 88x Wireless System... -
Page 16: Troubleshooting
Troubleshooting Issue Solutions Make sure that the transmitter and receiver are both powered on. Ensure the transmitter’s batteries are installed correctly. Check that the transmitter is not muted. Confirm that the CR88x adapter is correctly connected and plugged into an electrical outlet. Turn on the CR88x receiver. -
Page 17: Specifications
Dimensions (LxWxH) 8.25" x 4.9" x 1.75" 210mm x 125mm x 44mm Weight 0.88 lb / 400 g At Samson, we are continually improving our products, therefore specifications and images are subject to change without notice. Concert 88x Wireless System... - Page 18 ª Licensing: Note that a ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements. Licensing of Samson wireless microphone equipment is the user’s responsibility, and licensability depends on the user’s...
- Page 20 Having Trouble with your Concert Wireless System? We can help! CONTACT OUR SUPPORT TEAM: support@samsontech.com Our experts can help you resolve any issues. Follow us: @samson @samsontech @samson_technologies Samson Technologies 278-B Duffy Ave Hicksville, NY 11801 Phone: 1-800-3-SAMSON www.samsontech.com...
Need help?
Do you have a question about the CONCERT 88X and is the answer not in the manual?
Questions and answers