Autocall TrueAlert ES Installation Instructions Manual

TrueAlert ES Addressable Ceiling Mount Visual Indoor Notification Appliances Installation
Cautions, warnings, and regulatory information
Important: When the notification appliance emits light or sound, it indicates the possibility of an emergency situation that requires immediate atten-
tion of all occupants.
SAFETY: Always install, maintain, and test notification appliances within their specifications. Failure to follow all safety precautions and instructions
may result in loss of life and property due to non-functioning notification appliances. Some notification appliances use high voltage. To avoid electrical
hazards and avoid damage to appliances, make sure that the electrical power for the Notification Appliance Circuit is disconnected at the control
panel before installing, repairing, or internally adjusting any notification appliances. Even with electrical power removed, some notification appliances
(such as visible strobes) store a high voltage charge. The high voltage can cause injury resulting in death from electrical shock. DO NOT TOUCH
EXPOSED CIRCUITRY.
LOCATION REFERENCE: Location and quantity of appliances required must conform to the applicable local standards and guidelines (the National
Fire Alarm and Signaling Code (NFPA 72); ULC Standard CAN/ULC-S524, Installation of Fire Alarm Systems; the appropriate model building codes,
etc.) and specific requirements of the Local Authority Having Jurisdiction (AHJ). These notification appliances are not intended for installation within
hazardous locations as defined by the National Electrical Code (NEC) or NFPA.
UL Listed TrueAlert ES indoor product identification reference
Type
TrueAlert ES Ceiling Mount Visible
Only (VO) Appliance
Kit Contents
Not Included
Note: For information about appliance testing, see TrueAlert ES Addressable Appliances Troubleshooting Guide (579-1049AC).
Mounting instructions
1. Select the correct location and install the electrical box using screws suitable for the mounting surface.
2. Connect the building wires to the terminal block on the rear of the appliance. See
3. Use the hardware provided to secure the appliance to the electrical box. Installing the appliance using a single gang electrical box requires a
49VO-APCS adapter plate. You can mount the adapter plate in two orientations, see
4. Set the appliance settings. See
5. Attach the cover to the appliance.
Models
Components:
A49VO-APPLC
A49VO-APPLC-BA
A49VOH-APPLC
A49VOH-APPLC-BA
A49VOH-APPLCA
A49VOH-APPLCA-BA
A49VOH-APPLCB
A49VOH-APPLCB-BA
Accessories:
49VO-APCS
Covers:
A49VOC-CRALT
A49VOC-CRBF
A49VOC-CRFEU
A49VOC-CRF
A49VOC-CRS
Appliance x1, with 8-32 1 in. mounting screws x 2.
Order a cover separately for each appliance.
Electrical box, 1.5 in. (3.81 cm) minimum depth required, 4 in. (10.16 cm) square or single gang with an adapter
plate.
49VO-APCS adapter plate for use with the single gang electrical box, with 4-40 screws x2, and 6-32 screws x 2.
Setting the address DIP switch.
Cover colors
A49VOC-CWALT • Red
A49VOC-CWBF • White
A49VOC-CWFEU • Black
A49VOC-CWF
A49VOC-CWS
A49VOC-CK
A49VOC-CRBAF
A49VOC-CRBCF
A49VOC-CWBAF
A49VOC-CWBCF
A49VOC-CRBAA
A49VOC-CWBAA
Wiring instructions.
Wiring instructions.
Instructions
Operation
These appliances provide a visible
only (VO) warning of an alarm
condition when activated from the
control panel of a compatible UL/
ULC Listed, Autocall Fire Alarm
System. Consult Autocall Fire
Alarm panel documentation for
compatibility information.
VO models '49VOH' have Hi
intensity strobes; models '49VO'
have standard range strobes.
579-1227AC Rev D
*05791227ACD*