Advertisement
Air Cut-Off Tool Model No. GSA25 when operated in accordance with these instructions and tested in
accordance with EN 28662-2: 1994 results in the following vibration emission declared in accordance with
BS EN12096: 1996.
Measured vibration emission value: . . . . . . . . . . .3.9m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.6m/s²
these values are suitable for comparison with emission levels of other tools that have been subject to
the same test.
this tool may cause hand-arm vibration syndrome if its use is inadequately managed.
recommended Measures to reduce risk of hand-arm vibration syndrome:
This tool should not be used by an individual regularly for more than 402.5 minutes in any 8 hour period.
This duration of use should be reduced if the individual is exposed to hand-arm
2.
introDuction & sPecifications
Sealey's Generation or G3 series of air tools represents some of the best design innovations in air tools of recent
date. The tools feature contoured, soft-grip handles and housings which help reduce the effects of vibration and
chill – major contributors to circulatory and nerve problems such as white finger. The tools also include exhaust
systems designed to reduce noise levels by baffling the noise or directing it away from the operator's environment.
Most of the tools include integral and adjustable air valves for precise control of output. The air wrenches are,
pound for pound, amongst the most powerful machines we have seen in the market and the materials and
manufacturing techniques used in the production of all the G3 series will ensure long and reliable service.
Disc Size: . . . . . . . . . . . . . . . . . . . . . . Ø75 x 2 x 10mm
Free Speed: . . . . . . . . . . . . . . . . . . . . . . . . . 20000rpm
Air Consumption: . . . . . . . . . . . . . . . . . . . . . . . . . 4cfm
Operating Pressure: . . . . . . . . . . . . . . . . . . . . . . . 90psi
Air Inlet Size: . . . . . . . . . . . . . . . . . . . . . . . . . .1/4"BSP
3.
PreParinG tooL for use
3.1
air supply
recommended hook-up procedure is shown in fig 1.
3.1.1 Ensure tool air valve (or trigger) is in "off" position before connecting to the air supply.
3.1.2 You will require an air pressure of 90psi, and an air flow according to specification.
3.1.3 WarninG! Ensure the air supply is clean and does not exceed 90psi while operating the tool. Too
high an air pressure and unclean air will shorten the product life due to excessive wear, and may be
dangerous causing damage and/or personal injury.
3.1.4 Drain the compressor's air tank daily. Water in the air line will damage the tool.
3.1.5 Clean the compressor's air inlet filter weekly.
3.1.6 line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The
minimum hose diameter should be 1/4" I.D. and fittings must have the same inside dimensions.
3.1.7 Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all
connections are secure.
3.2
couplings.
Vibration may cause failure if a quick change coupling is connected directly to the tool.
To overcome this, connect a leader hose to the tool. A quick change coupling may then be used to
connect the leader hose to the air line recoil hose. See fig 1 & 2.
fig 1
risk of Hand arm Vibration injury
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.9kg
Cutting Disc No: . . . . . . . . . . . . . . . . . . Single: PTC/3C
. . . . . . . . . . . . . . . . . . . . . . . . . . . Pack of 5: PTC/3C5
Noise Pressure. . . . . . . . . . . . . . . . . . . . . . . . . 80dB.A
Original Language Version
vibration from other sources.
fig 2
GSA25
Issue: 3 - 10/11/10
Advertisement
