Advertisement
3.2.2
Torque Setting
Torque is the amount of turning force applied when you use the drill.
Torque setting ‘1’ (fig 3 ‘C’) is the lowest and will apply the least effort - to the final turns of a screw, for example.
The torque becomes progressively greater with increased setting numbers, up to a maximum of ‘6’.
The combination of variable speed and torque gives maximum drilling efficiency.
Suggested torque settings:
3.2.3
To Drill Holes
Lock a pilot drill (smaller size drill than the finished hole size) into the chuck.
Select an appropriate torque setting (para. 3.2.2.).
Check to confirm the turning direction is correct.
DO NOT attempt to change direction whilst the drill is running.
Drill a pilot hole in the middle of the spot where the final hole is to be drilled.
Insert the final sized drill bit. Hold drill firmly and place the drill bit at the entrance of the pilot hole and press the trigger as in 3.2.1.
If the drill becomes stuck, release the switch and place the drill in reverse by pressing the direction switch to the other side. If this
does not work, gently work the drill bit free. If the chuck stops turning, check the torque setting.
3.2.4
As a Screw or Bolt Driver
Lock appropriate tool bit in the chuck, set appropriate torque and proceed with the task. To remove screws, bolts, etc., switch the drill
to reverse.
3.2.5
When you have finished working, remove the bit from the chuck, clean drill and bit and store in the carry case.
4. PARTS LIST
ITEM
PART NO.
DESCRIPTION
01.
CP12035V.01
SCREW
02.
CP12035V.02
CHUCK
03.
CP12035V.03
SCREW
04.
CP12035V.04
RING
05.
CP12035V.05
TORQUE SETTING RING
06.
CP12035V.06
RING SPACER
07.
CP12035V.07
SPRING
08.
CP12035V.08
SPACER
09.
CP12035V.09
STEEL BALL
10.
CP12035V.10
GEAR BOX
11.
CP12035V.11
SCREW
12.
CP12035V.12
CONNECTION CLIP FOR GEAR
13.
CP12035V.13
MOTOR GEAR
14.
CP12035V.14
SCREW
15.
CP12035V.15
MOTOR
16.
CP12035V.16
HOUSING (RIGHT)
17.
CP12035V.17
SCREW
18.
CP12035V.18
SWITCH ASS’Y
19.
CP12035V.32
HOUSING (LEFT)
20.
CB18VBP
BATTERY 18V
21.
CP1801VC
MAINS ADAPTOR & CHARGER
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts
without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12 months from
purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and promotions call us on
01284 757525 and leave your full name and address, including postcode.
Declaration of Conformity
CORDLESS DRILL/DRIVER AND
CHARGER
Models: CP1801V, CP1801VC
73/23/EEC LV Directive
89/336/EEC EMC Directive
93/68/EEC Marking Directive
01284 757500
1 - Small screws
2 - Screws into soft material
3 - Screws into hard material
We, the sole importer into the UK, declare that the products listed here are in conformity with the following standards and directives.
The construction files for these products are held by the Manufacturer and may be inspected,
by a national authority, upon request to Jack Sealey Ltd.
Signed by Mark Sweetman
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.
01284 703534
4 - Screws into hard wood
5 - Regular drilling
6 - Heavy drilling
6th January 2005
www.sealey.co.uk
Web
fig 3
Issue:
Issue Date:
060105
For Jack Sealey Ltd.
Sole importer into the UK
of Sealey Power Tools.
sales@sealey.co.uk
email
CP1801V - 1 - 060105
1
Advertisement
