Advertisement
MOVEO
OPERATORE IRREVERSIBILE PER
CANCELLI SCORREVOLI
IRREVERSIBLE OPERATOR FOR
SLIDING GATES
OPERATEUR IRREVERSIBLE POUR
PORTAILS COULISSANTES
OPERADOR IRREVERSIBLE PARA
VERJAS CORREDERAS
SELBSTHEMMENDER
TORANTRIEB FÜR SCHIEBETOREN
6-1624870 /R.1
Operatore
Operateur
Operator
Operador
Torantrieb
MOVEO 800
MOVEO 600
MOVEO 600
MOVEO 700 24V
Alimentazione
Centralina
Power Supply
Control unit
Alimentation
Centrale de commande
Alimentacion
Cuadro de mando
Stromspannung
Steuereinheit
230V 50/60Hz
BIOS1
230V 50/60Hz
BIOS1
120V 50/60Hz
BIOS1 120
24Vdc
BIOS1 24
Codice
Code
Code
Codigo
Code
12007922
12007920
12007930
12007950
Advertisement
Table of Contents
Related Manuals for Allmatic MOVEO 600KG 230V
Summary of Contents for Allmatic MOVEO 600KG 230V
- Page 1 MOVEO OPERATORE IRREVERSIBILE PER CANCELLI SCORREVOLI IRREVERSIBLE OPERATOR FOR SLIDING GATES OPERATEUR IRREVERSIBLE POUR PORTAILS COULISSANTES OPERADOR IRREVERSIBLE PARA VERJAS CORREDERAS SELBSTHEMMENDER TORANTRIEB FÜR SCHIEBETOREN 6-1624870 /R.1 Operatore Alimentazione Centralina Codice Operateur Power Supply Control unit Code Operator Alimentation Centrale de commande Code Operador Alimentacion...
-
Page 2: Electrical Connections
3 internal and 3 external (better if complete of syncronism feature). N.B.: The system must be grounded Data described by this manual are only Indicative and ALLMATIC reserves to modify them at any time. Install the system complying with current standards and regulations. -
Page 3: System Layout
Irreversible operating devices for sliding gates. The irreversibility of this operating device allows you to avoid using any electric lock for an effective closing of the gate. The motor is protected by an heat probe, that temporary interrupts the operating cycle in case of prolonged use. TECHNICAL FEATURES MOVEO 600KG 230V MOVEO 800KG 230V MOVEO 600KG 120V MOVEO 700KG 24V Code... -
Page 4: Base Plate Installation
BASE PLATE INSTALLATION 1. Push the achors until they are 90° as shown in the picture 2. Insert the 4 screws (supplied) as shown in the image, from the bottom to the top of the backing plate 3. Screw completely the 4 nuts (supplied) as shown in the image 4. - Page 5 MOTOR FITTING Fig. 5 To fix the motor to the counterplate, insert and screw the 4 nuts (Fig. 5). Position the motor in parallel with the gate and with the gear under the rack as shown in Fig. 8. N.B. It is important to energetically tighten the 4 nuts, making sure that the gearmotor is firmly on the ground during the entire stroke of the gate. RACK FITTING The rack must be fixed at a certain height with respect to the motor fixing plate (Fig.
- Page 6 LIMIT SWITCH FITTING In order to determine the gate travel length, place two cams (Fig. 9) at the ends of the rack (Fig. 10). Move the cams on the rack teeth to adjust their opening and closing travel. To fix the cams to the rack, tighten the screws issued. Note: In addition to the electric stop cams mentioned above, you must also install strong mechanical stops preventing the gate from sliding out from the top guides.
-
Page 7: Disposal Of The Product
Fig. 13 Fig. 13 For special installations request information from Allmatic or use larger geared motors. RELEASE To move the gate manually it is necessary to release the gearmotor inserting the key, turning it for 90° and open the lever (Fig. 14). - Page 8 ALLMATIC S.r.l 32020 Borgo Valbelluna - Belluno – Italy Via dell’Artigiano, n°1 – Z.A. Tel. 0437 751175 – 751163 r.a. www.allmatic.com - E-mail: info@allmatic.com 6-1624870...
Need help?
Do you have a question about the MOVEO 600KG 230V and is the answer not in the manual?
Questions and answers