Table of Contents
Advertisement
FCC Part 15 C Notice
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
This equipment should be installed and operated with minimum distance 20cm between the radiator and
your body.
environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20
cm entre le radiateur et votre corps.
INDUSTRY CANADA NOTICE: CANADA ONLY.
Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes :
1. L'appareil ne doit pas produire de brouillage;
2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
This product is manufactured by Amax Group
12645 Memorial Drive Suite F1 #388 Houston, TX 77024
Propel™ and Propel RC™ are the licensed trademarks of Rooftop Group LTD Singapore.
2008 All rights reserved. Visit us at www.propelrc.com
CAN ICES-3(B)/NMB-3(B)
This product meets the applicable Innovation, Science and Economic Development Canada
technical specifications.
Conforms to safety requirements of FCC, RSS247, RSS210.
15
Compact Folding Drone with HD Camera
WARNING: Never leave product charging unattended for extended periods of
time. Always disconnect the battery from charger immediately after the battery
WARNING!
CHOKING HAZARD - Small parts.
Not suitable for children under 3 years.
SNAP 2.0™
2.4G Wireless
Made in China
Colors and styles may vary slightly .
V1.0
SNAP 2.0
INSTRUCTION BOOKLET
is fully charged. Please refer to enclosed safety instructions.
PACKAGE CONTAINS:
Spare Parts
USB Charger
Phone Holder
Controller
TM
ON BOARD
ON BOARD
HD CAMERA
HD VIDEO
1280 x 720 pixel
30 frames per second
Foot Pad
Battery
Instruction
Manual
PROPEL
Advertisement
Table of Contents
Related Manuals for Propel Trampolines SNAP 2.0
Summary of Contents for Propel Trampolines SNAP 2.0
- Page 1 FCC Part 15 C Notice SNAP 2.0 CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
-
Page 2: Table Of Contents
Charging the SNAP 2.0™ Li-Poly Battery........ -
Page 3: Snap 2.0™ Diagram
SNAP 2.0™. Make sure that there are no other 2.4G devices in the area. 2. Insert the battery into the SNAP 2.0™ and set it down on a flat level surface. Push down the power button CONTROLLER DIAGRAM and hold for a few seconds (see diagram D1).The red and white LED lights on the drone should begin to flash... -
Page 4: Now You Are Ready To Fly
Below is a list of basic flight functions for your long-range remote to control the SNAP 2.0™. While learning to fly your SNAP 2.0™ it is best to start in a large space with the drone facing away from you until you get used to the basic controls. -
Page 5: Adjusting The Trim
Forward/Backward Trim 2. Make sure the SNAP 2.0™ is on and that the controller is synced (refer to syncing pg 4). Do not start the blades. Instead move both the throttles and control stick down and to the right corner and hold them there for 5 seconds(see diagram R). -
Page 6: Live Video Streaming Setup
2. In the Settings menu of your device, locate the Wi-Fi option. 3. Turn ON the Wi-Fi option. 4. Select “Propel 1890” from the Wi-Fi list. Wait for your SNAP 2.0™ to be connected. Return to the Main Menu. Settings Propel1890 Note: Apple®... -
Page 7: Troubleshooting Your Snap 2.0
Crash landing at high-speed may cause damage to your SNAP 2.0™’s propellers. 1. The SNAP 2.0™ has four sets blades, two sets blades with indication number B & A on front, and two sets blades with indication number A & B on the rear (see the diagram V). -
Page 8: Warnings
Stand away from the SNAP 2.0™ to reduce the risk of getting into the flight path. Warn spectators that you will be flying your SNAP 2.0™ so that they are aware of its position.
Need help?
Do you have a question about the SNAP 2.0 and is the answer not in the manual?
Questions and answers