Advertisement
Quick Links
The HydroSweep® Pro ACD (Aquatic Current Device) is designed to help preserve your waterfront and control algae,
trash, and decaying debris on the surface of the water, while maintaining naturally occurring aquatic life. For optimal
results, the HydroSweep® Pro ACD should be positioned twelve inches (12") off the floor of your waterfront and
positioned level (see page 4). Setting the pump too close to the bottom of the body of water may have an adverse impact
on the shoreline and aquatic life, which may be illegal in some jurisdictions including Minnesota. You should check with
your local ordinances regarding any limitations on use. Upon start-up of the HydroSweep® Pro ACD, the water may
initially appear dirty since debris, silt, and sediment are being moved from the bottom of the body of water. This should
settle in time.
Installation and Operating Instructions
Technical Support: 1-800-993-2114 ext. 1
THERE IS A SERIOUS RISK OF ELECTRIC SHOCK IF THE
HydroSweep® Pro ACD IS NOT PROPERLY ASSEMBLED, HANDLED
OR INSTALLED. WE RECOMMEND THAT YOU USE A LICENSED
ELECTRICIAN. THE UNIT MUST BE CONNECTED TO A GFCI (15 OR
20 AMP) CIRCUIT.
PLEASE READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY
(SEE ADDITIONAL PRODUCT WARNINGS ON THE LAST PAGE)
Inspect the HydroSweep® Pro ACD for damage immediately upon
delivery. IF THE PRODUCT IS DAMAGED, STOP: DO NOT USE A
DAMAGED PRODUCT. Report any damage to your dealer.
Tools Required:
Difficulty Level: Intermediate
•
•
•
•
Screen Kit (Optional):
•
(1) 3/4" Wrenches or Sockets
(2) 9/16" Wrenches or Sockets
Cordless Drill (optional)
Phillips Screw Driver
11/32" Wrench or Socket
2431 Galpin Court, Suite 140, Chanhassen, MN 55317
1-800-993-2114
Advertisement
Related Manuals for SafeShore HydroSweep Pro
Summary of Contents for SafeShore HydroSweep Pro
- Page 1 Installation and Operating Instructions Technical Support: 1-800-993-2114 ext. 1 THERE IS A SERIOUS RISK OF ELECTRIC SHOCK IF THE HydroSweep® Pro ACD IS NOT PROPERLY ASSEMBLED, HANDLED OR INSTALLED. WE RECOMMEND THAT YOU USE A LICENSED ELECTRICIAN. THE UNIT MUST BE CONNECTED TO A GFCI (15 OR 20 AMP) CIRCUIT.
-
Page 2: Parts List
Parts List Shaft Cap Shaft Rotator Assembly Collar Shaft Support Bracket Bail Pump Assembly... - Page 3 1. Attach the shaft to the bail using the included 3/8”x2 Shaft 1/4” bolt and 3/8” brass nyloc nut. Bail 2. Remove the shaft cap and slide the shaft support Shaft Support bracket onto the bracket shaft. 3. Slide the rotator over the shaft just like sliding on the shaft support...
- Page 4 HydroSweep Pro into the dock bracket and tighten the position locking bolt. 7. Ensure the Hydrosweep Pro is positioned 12” off the floor of the lake and slide the shaft support bracket up and slide the pin through the rotator.
-
Page 5: Using The Keypad
Using the Keypad When programming, avoid sweeping past dock wheels to prevent excavation of floor under wheels. Turns unit counter Turns unit clockwise clockwise when programming when programming Eco-Mode runs 24 hours on and 24 hours off Rotates 1 degree every Off... - Page 6 140, Chanhassen, MN 55317. When you seek service under this warranty, you will need to provide the original dated bill of sale from the service center. SafeShore®, in its sole discretion, will repair or replace the product at no charge if the damage is determined by SafeShore® to be covered under the limited warranty. If the damage is not covered by the limited warranty, repairs will be conducted at SafeShore®’s standard rate for parts and labor and you agree to...
Need help?
Do you have a question about the HydroSweep Pro and is the answer not in the manual?
Questions and answers