Zanussi ZDT26030FA User Manual
  1. Manuals
  2. Brands
  3. Zanussi Manuals
  4. Dishwasher
  5. ZDT26030FA
  6. User manual

Zanussi ZDT26030FA User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

User Manual
GETTING
STARTED?
EASY.
ZDT26030FA
EN User Manual
Dishwasher

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ZDT26030FA and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Zanussi ZDT26030FA

Summary of Contents for Zanussi ZDT26030FA

  • Page 1 User Manual GETTING STARTED? EASY. ZDT26030FA EN User Manual Dishwasher...

  • Page 2: Safety Information

    SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damage that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
  • Page 3 If the supply cord is damaged, it must be replaced by the • manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends • pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down.
  • Page 4 WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. • Do not put flammable products or items that are wet with flammable products in, near or on the appliance.

  • Page 5: Easy Start

    EASY START On/off button XtraDry button Display Delay button Programme button (up) CANCEL button Programme button (down) Indicators TimeManager button INDICATORS End indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates. BEAM-ON-FLOOR The Beam-on-Floor is a light that shows on the kitchen floor below the appliance door.

  • Page 6: Programme Selection Mode

    Consumption values Degree of soil Programme Programme phases Type of load Duration Energy Water (min) (kWh) Normal soil • Prewash 0.920 Crockery and • Wash 50 °C cutlery • Rinses • • Prewash 44 - 160 0.6 - 1.5 6 - 12 Crockery, cut- •...

  • Page 7: User Mode

    CANCEL PROCEDURE As the appliance stores the saved settings, there is no need to configure it before every cycle. Use CANCEL to: • Cancel a currently running programme. ADJUSTING THE WATER SOFTENER • Stop the countdown of Delay option. • Bring the appliance back to the programme Make sure the appliance is in user mode.

  • Page 8: Before First Use

    DEACTIVATING THE RINSE AID EMPTY 2. Press to change the setting. NOTIFICATION 3. Press the on/off button to confirm the setting. Make sure the appliance is in user mode. HOW TO DEACTIVATE AIRDRY 1. Press AirDry improves the drying results with less energy •...

  • Page 9: Adding Rinse Aid

    The salt is used to recharge the resin in the water softener and to assure good washing results in daily use. Adding salt Before the first use, put one litre of water in the salt container. CAUTION! Water and salt can come out of the salt container during filling. To prevent corrosion, start a programme immediately after filling the salt container.

  • Page 10: Adding Detergent

    ADDING DETERGENT If the programme has a prewash phase, put a small quantity of detergent also in compartment B. ADDING MULTI-TABLETS • Adjust the water softener to the lowest level. SETTING AND STARTING A PROGRAMME 2. Press until the display shows the delay time you want to set (1-24h).

  • Page 11: Hints And Tips

    The washing results are the same as with the Do not try to close the appliance door normal programme duration. The drying results can within 2 minutes after AirDry decrease. automatically opens it, as this may If the option is not applicable to the programme, the cause damage to the appliance.

  • Page 12: Unloading The Baskets

    WHAT TO DO IF YOU WANT TO STOP USING • Put light items in the upper basket. Make sure MULTI-TABLETS that the items do not move. • Make sure that the spray arm can move freely Before you start to use separately detergent, salt before you start a programme.

  • Page 13: External Cleaning

    • Make sure that there are no residues of food or soil in or around the edge of the sump. • Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides. •...
  • Page 14 Problem and alarm code Possible cause and solution The program does not start. • Make sure that the appliance door is closed. • If the delay start is set, cancel the setting or wait for the end of the countdown. •...

  • Page 15: The Washing And Drying Results Are Not Satisfactory

    For alarm codes not described in the table, contact Refer to "Before first use", "Daily an Authorised Service Centre. use", or "Hints and tips" for other possible causes. Once you have checked the appliance, deactivate and activate the appliance. If the problem occurs again, contact an Authorised Service Centre.

  • Page 16: Product Information Sheet

    PRODUCT INFORMATION SHEET Trade Mark Zanussi Model ZDT26030FA 911536331 Rated capacity (standard place settings) Energy efficiency class Energy consumption in kWh per year, based on 280 standard cleaning cycles using cold water fill and the consumption of the low power modes. The actual energy consumption will de- pend on how the appliance is used.

  • Page 17: Additional Technical Information

    Drying efficiency class on a scale from G (least efficient) to A (most efficient) The ‘standard programme’ is the standard cleaning cycle to which the information in the label and the fiche relates. This programme is suitable to clean normally soiled tableware and is the most efficient programme in terms of combined energy and water consumption.
  • Page 20 WWW.ZANUSSI.COM/SHOP...

Table of Contents