Advertisement
Available languages
Available languages
Quick Links
WHAT'S IN THE BOX
• LED FIXTURE
WHAT YOU'LL NEED
• SAFETY GLASSES
• WIRE CUTTERS
• WIRING SUPPLIES AS SPECIFIED BY CODE
WARNING
• Turn off electrical power at fuse or circuit breaker box
before wiring fixture to the power supply.
• Turn off the power when you perform any
maintenance.
• Verify that supply voltage is correct by comparing it
with the luminaire label informaGon.
• Keep lens Gghtly closed when in operaGon.
• ModificaGons to the product voids the warranty.
CS SERIES
COMMERCIAL LINEAR STRIP
INSTALLATION INSTRUCTIONS
For use with:
LED Commercial Linear Strip:
CS-484-4 | CS-484-4-347
CS-484-MS-4 | CS-484-MS-4-347
IMPORTANT
Before assembling your fixture,
please make sure that you carefully
read through this instrucGon sheet.
Consider having your fixture installed
by a qualified licensed electrician.
Note: The important safeguards and
instrucGons that appear in this sheet
are not meant to cover all possible
condiGons and situaGons that may
occur. It must be understood that
common sense, cauGon, and care are
factors that cannot be built into any
product. These factors must be
supplied by the person(s) caring for
and operaGng the fixture.
PREMISE LED Inc.
82-86 Carrier Drive
Toronto, ON Canada
M9W 5R1
PREMISELED.COM
1
Advertisement
Summary of Contents for Premise CS Series
- Page 1 CS SERIES COMMERCIAL LINEAR STRIP INSTALLATION INSTRUCTIONS For use with: LED Commercial Linear Strip: CS-484-4 | CS-484-4-347 CS-484-MS-4 | CS-484-MS-4-347 IMPORTANT Before assembling your fixture, WHAT’S IN THE BOX please make sure that you carefully read through this instrucGon sheet. • LED FIXTURE Consider having your fixture installed by a qualified licensed electrician. Note: The important safeguards and WHAT YOU’LL NEED instrucGons that appear in this sheet are not meant to cover all possible condiGons and situaGons that may • SAFETY GLASSES occur. It must be understood that • WIRE CUTTERS • WIRING SUPPLIES AS SPECIFIED BY CODE common sense, cauGon, and care are factors that cannot be built into any product. These factors must be...
- Page 2 INSTALLATION INSTRUCTIONS 2. Remove the screws and aluminum 1. Remove the fixture lens cover via plate. the side of the fixture. 4. Screw the fixture housing into the 3. With the top of the fixture facing upwards, pass the power supply ceiling. from the bo`om through the entry hole. 6. Re-install the screws, aluminum plate, 5. Connect the power supply to the and fixture lens. terminal block. NOTE: If you are installing the fixture with integrated sensor (CS-484-MS-4 and CS-484- MS-4-347), please refer to the CORE MoGon Sensor Setup Guide.
- Page 3 • COUPE-FIL toutes les condiGons et les situaGons • FOURNITURE DE CÂBLAGE TEL QUE possibles qui puissent se produire. Il faut SPÉCIFIÉ PAR LES CODES ÉLECTRIQUES comprendre que le bon sens, la prudence et les soins sont des facteurs qui ne peuvent pas être intégrés dans un AVERTISSEMENT produit quelconque. Ces facteurs doivent être fournis pas la (les) personne(s) en charge du soin et du • Couper l’alimentaGon électrique au fusible ou à la boîte du foncGonnement de l’appareil. disjoncteur avant de câbler le luminaire sur l’alimentaGon. • Couper le courant électrique avant de faire la maintenance. • Vérifier que la tension d’alimentaGon est correcte en la comparant avec les informaGons de l’éGque`e du luminaire. • Durant le foncGonnement garder la lenGlle herméGquement PREMISE LED Inc. fermée. 82-86 Carrier Drive • Les modificaGons apportées au produit annulent la garanGe. Toronto, ON Canada M9W 5R1 PREMISELED.COM...
- Page 4 INSTRUCTIONS D’INSTALLATION 2. Enlever les vis et les plaques en 1. Voir la feuille en plasGque. aluminium. 4. Fixer le boîGer au plafond à l'aide de 3. Passer le fil de courant à travers le trou d'entrée. vis. 6. Reme`re les vis et la feuille en 5. Connecter la source d'alimentaGon plasGque. avec la terminal.
Need help?
Do you have a question about the CS Series and is the answer not in the manual?
Questions and answers