DeWalt DWE6000 Manual page 10

ENglISH
2. Using a 2 mm hex wrench turn locking lever
adjustment screw (p) in small increments.
Turning the screw clockwise tightens the lever,
while turning the screw counterclockwise
loosens the lever.
Motor Quick Release (Fig. 2)
1. Open the locking lever (o) on the base.
2. Grasp the motor unit with one hand, depressing
both quick release tabs (n).
3. With the other hand, grasp the base and pull
motor from the base.
Inserting and Removing a Cutter Bit
(fig. 5)
1. Separate the motor unit (b) from the base.
2. Hold the motor unit (b) while pressing the
spindle lock button (f).
3. Insert the cutter shaft (u) in the collet (h).
4. Tighten the collet nut (i) using the
17 mm wrench.
5. To remove the cutter, hold the motor shaft while
pressing the spindle lock (f).
6. Using the 17 mm wrench, loosen the collet
nut (i) a few turns and remove the cutter.
Replacing the Collet (fig. 5)
The Laminate Trimmer is supplied with an 6 mm
(1/4")collet fitted to the tool.
1. Loosen the collet nut (i) completely.
2. Remove the collet (h) and replace it.
3. Tighten the collet nut (i).
NOTE: Never tighten the collet nut (i) without first
installing a router bit in it. Tightening an empty collet
nut, even by hand, can damage the collet (h).
Depth of Cut Adjustment (fig. 3, 4)
WARNING: To reduce the risk of
injury, turn off and disconnect it from
the power source before installing and
removing accessories, before adjusting
or when making repairs. An accidental
start-up can cause injury.
1. Select and install the desired cutter. Refer to
Inserting and Removing a Cutter Bit.
2. Insert motor into base, ensuring base is
attached to the adjustment ring (c). Place
laminate trimmer on the work piece.
8
3. Open the locking lever (o) and turn the depth
adjustment ring (c) until the cutter touches the
work piece. Turning the ring clockwise raises
the cutter while turning it counterclockwise
lowers the cutting head.
4. Turn the micro adjustment scale (d) until the 0
on the scale lines up with the pointer on the
quick release tab (n).
5. Turn the depth adjustment ring until the pointer
lines up with the desired depth of cut marked
on the micro adjustment scale.
NOTE: Each mark on the adjustment scale
represents a depth change of 0.5mm.
6. Close the locking lever (o) to lock the base.
Attaching the Dust Extraction
Adaptor (Fig. 8)
The dust extraction adaptor (v) can be attached to
the front of the sub base underneath the locking
lever as shown in figure 8. Hand tighten both finger
screws (w) and attach a vacumm hose to the dust
exhaust port (x).
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Proper Hand Position (fig. 7)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the
motor base with the other hand on the motor cap
as shown.
Starting and Stopping the Motor
(Fig. 1, 2)
To turn unit on, pull the on/off switch (a) up. To turn
the unit off, depress the switch back down into the
motor housing. Refer to Figure 2.