Related Manuals for Twinny Load Swing CK
Summary of Contents for Twinny Load Swing CK
- Page 1 Twinny Load Swing CK ® Twinny Load Compact PA ® Montagevoorschrift en gebruiksaanwijzing Montage- und Gebrauchsanleitung Installation and use instructions Instructions de montage et mode d’emploi EEC e4 * 79/488 * 87/354 * 0029 ***...
- Page 2 Erinnerung: Type drager: Trägertyp: ❏ Traditional C ❏ Prestige PS ❏ Traditional CK ❏ Prestige PA ❏ Swing CK ❏ Compact PA ❏ Swing FK ❏ Compact RP ❏ Ergo CK ❏ Prestige ECO ❏ Ergo FE ❏ Perfect ECO ❏...
- Page 3 U kunt er nu zorgeloos met de auto en fietsen op uit trekken. Gewoon, lekker actief zijn en nieuwe routes verkennen. We wensen u veel plezier met uw nieuwe fietsdrager. Wir gratulieren Ihnen zum Kauf Ihres neuen Fahrradträgers von Twinny Load ®...
- Page 4 75 kg. The weight of the Twinny Load Swing CK is 12.9 kg. You can find the weight of your bicycle in the ® supplied booklet or perhaps on the Internet.
- Page 5 - Never use straps or ropes to fasten your bicycle. These can irreparably damage the frame of your bicycle. - In principle, an electrical bicycle fits on a Twinny Load bicycle carrier. This depends on the brand and type of electrical bicycle. You will find a fitting table on the homepage of our website.
- Page 6 Installation of number plate Break four lugs out of the light bar and place them in the cut-aways. Beware! Slide short Belgian number plate up to the first stop. Austrian number plate can be installed without lugs. Slide the number plate into the light bar up to the second stop.
- Page 7 Installation of bicycle carrier Open the spindle to such an extent that the clamp pieces can be Place the bicycle carrier on pushed downwards with the catch on the side. the towing hook and push the carrier downwards. Fix it by tightening the spindle Lock the bicycle carrier.
- Page 8 Installation of light units Take the light units out of Place the light units in Width adjustment: press the red the storage position and slide the light bar, press the red unlocking device and slide the them into the guide of the light unlocking device and slide light units out in steps of 1 cm.
- Page 9 Placing of bicycle Slide out the wheel rails Loosen the straps and turn Remove the clamp from halfway and tighten them. them downwards. the holder. Place the first bicycle in the Position the pedal arm in front of the holder. Hook the clamp wheel rails closest to the car over the projecting steel lugs.
-
Page 10: Extra Setting
Cont. placing of bicycle Place the second bicycle with the handlebars to the right and the left pedal downwards. Tighten the clamp. Lock the clamp. Extra setting The bicycles touch each other. The bicycle touches the lid of the boot. The bicycle touches the lid of the boot: adjust the holder in such way that the bicycle doesn’t touch the lid of the boot. - Page 11 The pedal arm is too high, the clamp does not fit, the bicycle stand is in the way. Install the holder one position higher by pulling the securing clip out of the axle and then installing the axle and support in the higher position and apply the securing clip again. Tilting of carrier Move the bolt upwards to Move the bolt towards you and tilt the bicycle carrier calmly...
- Page 12 Storage of light unit Push in the red unlocking Position the projecting guides Push the light unit down into device and slide the light unit of the light unit in the back of the clamp. out of the light bar. the light bar.
- Page 13 The guarantee consists of free repair or replacement of parts in case of material and construction errors. The guarantee is effective after you have activated the guarantee certificate on the Twinny Load website www.twinnyload.com or via sending the reply card supplied with the guarantee certificate.
- Page 14 www.twinnyload.com...
Need help?
Do you have a question about the Swing CK and is the answer not in the manual?
Questions and answers