All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by ER/EL 1065 BU TV Consumer Care, the Netherlands...
Figures can deviate due to the different set executions. • Specifications are indicative (subject to change). Directions for Use You can download this information from the following websites: http://www.philips.com/support http://www.p4c.philips.com Technical Specifications For on-line product support please use the CTN links in Table 2-1.
Page 3
Technical Specifications, Diversity, and Connections Q551.1E LA EN 3 Table 2-1 Described Model Numbers and Diversity Mecha- nics Descriptions Schematics Styling 32PFL8605H/12 Monet 64064 2-1 4-1 4.4 7.2 7.5.1 7.10 7.11 9-1 10-1 10-10 10-15 10-17 10-19 10-21 10-23 10-33 10-35 11-1 10-42 10-6...
Page 4
EN 4 Q551.1E LA Technical Specifications, Diversity, and Connections Connections SIDE CONNECTORS REAR CONNECTORS BOTTOM CONNECTORS 18750_117_100423.eps 100423 Figure 2-1 Connection overview 8000 series (Monet) REAR CONNECTORS SIDE CONNECTORS NETWORK SD CARD SERVICE DVI HDMI UART AUDIO IN BOTTOM CONNECTORS...
Page 5
Technical Specifications, Diversity, and Connections Q551.1E LA EN 5 Note: The following connector colour abbreviations are used - D0+ Data channel (acc. to DIN/IEC 757): Bk= Black, Bu= Blue, Gn= Green, Gy= - Shield Grey, Rd= Red, Wh= White, Ye= Yellow. - D0- Data channel 10 - CLK+...
Page 6
EN 6 Q551.1E LA Technical Specifications, Diversity, and Connections 8 - EXT3: Cinch: Video YPbPr - In, Audio - In 16 - DDC_SDA DDC data Gn - Video Y / 75 ohm 17 - Ground Bu - Video Pb 0.7 V / 75 ohm 18 - +5V Rd - Video Pr...
3.3.3 Spare Parts external damage. • Check the strain relief of the Mains/AC Power cord for For the latest spare part overview, consult your Philips Spare proper function. Part web portal. • Check the electrical DC resistance between the Mains/AC...
Page 8
EN 8 Q551.1E LA Precautions, Notes, and Abbreviation List The third digit in the serial number (example: Abbreviation List AG2B0335000001) indicates the number of the alternative B.O.M. (Bill Of Materials) that has been used for producing the 0/6/12 SCART switch control signal on A/V specific TV set.
Page 9
6.5 MHz. L' is Band (VESA standard for communication I, L is all bands except for Band I channel and display). Using E-DDC, LG.Philips LCD (supplier) the video source can read the EDID Loudspeaker information form the display.
Page 10
SOPS Self Oscillating Power Supply Serial Peripheral Interface bus; a 4- wire synchronous serial data link standard S/PDIF Sony Philips Digital InterFace SRAM Static RAM Service Reference Protocol Small Signal Board Spread Spectrum Clocking, used to reduce the effects of EMI...
Mechanical Instructions Q551.1E LA EN 11 4. Mechanical Instructions Index of this chapter: 4.1 Cable Dressing Monet Styling (8000-series) 4.2 Cable Dressing Rubens Styling (9000-series) 4.3 Service Positions 4.4 Assy/Panel Removal Monet Styling 4.5 Assy/Panel Removal Rubens Styling 4.6 Set Re-assembly Notes: •...
Page 12
EN 12 Q551.1E LA Mechanical Instructions Cable Dressing Rubens Styling (9000-series) 18750_100_100414.eps 100414 Figure 4-2 Cable dressing 32PFL9705x/xx (applicable to all 9000 sets) Service Positions 4.4.2 Speakers Tweeters For easy servicing of a TV set, the set should be put face down Each tweeter unit is mounted with two screws.
Page 13
Mechanical Instructions Q551.1E LA EN 13 18750_104_100414.eps 100414 Figure 4-5 Ambilight units 1. Unplug the flat foil(s) [1]. 2. Release the clips [2] that secure the PWB. 3. Slide the PWB out of the set [3]. 4.4.7 IR & LED Board Refer to Figure 4-6 Figure 4-7...
Page 14
EN 14 Q551.1E LA Mechanical Instructions 4.4.9 LCD Panel Assy/Panel Removal Rubens Styling Refer to Figure 4-8 Figure 4-10 for details. The instructions apply to the 32PFL9705x/xx. 4.5.1 Rear Cover Warning: Disconnect the mains power cord before you remove the rear cover. 1.
Page 15
Mechanical Instructions Q551.1E LA EN 15 4.5.4 Ambilight Units 4.5.6 IR & LED Board Refer to Figure 4-12 Figure 4-13 for details. Refer to Figure 4-15 for details. Note: the Ambilight units are to be swapped on PWB level. 18750_113_100415.eps 100415 Figure 4-12 Rim 18750_112_100415.eps...
Page 16
EN 16 Q551.1E LA Mechanical Instructions Set Re-assembly To re-assemble the whole set, execute all processes in reverse order. Notes: • While re-assembling, make sure that all cables are placed and connected in their original position. • Pay special attention not to damage the EMC foams in the set.
Service Modes, Error Codes, and Fault Finding Q551.1E LA EN 17 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: • All service-unfriendly modes (if present) are disabled, like: 5.1 Test Points – (Sleep) timer. 5.2 Service Modes –...
Page 18
“OK” button on the RC. Code Contents of SAM (see also Table 6-12) 39mm • Hardware Info. PHILIPS – A. SW Version. Displays the software version of the MODEL: 32PF9968/10 main software (example: Q555X-1.2.3.4 = PROD.SERIAL NO: AG 1A0620 000001 AAAAB_X.Y.W.Z).
Page 19
Service Modes, Error Codes, and Fault Finding Q551.1E LA EN 19 • NVM editor. For NET TV the set “type number” must be How to Activate CSM entered correctly. Also the production code (AG code) can be entered here Key in the code “123654” via the standard RC transmitter. via the RC-transmitter.
Page 20
EN 20 Q551.1E LA Service Modes, Error Codes, and Fault Finding S : 0000 000X (number of software events : SW EVENT- Stepwise Start-up LOG #(events) H : 000X 0000(number of hardware errors) When the TV is in a protection state due to an error detected by H : 0000 000X (number of hardware events : SW EVENT- stand-by software (error blinking is displayed) and SDM is LOG #(events).
Page 21
Service Modes, Error Codes, and Fault Finding Q551.1E LA EN 21 Stand by or Mains is applied Protection Standby Supply starts running. All standby supply voltages become available. st-by µP resets If the protection state was left by short circuiting the Initialise I/O pins of the st-by µP: SDM pins, detection of a protection condition during - Switch reset-AVC LOW (reset state)
Page 22
EN 22 Q551.1E LA Service Modes, Error Codes, and Fault Finding Reset-system is switched HIGH by the Reset-system is switched HIGH by the AVC at the end of the bootscript AVC at the end of the bootscript AVC releases Reset-Ethernet, Reset-USB and AVC releases Reset-Ethernet, Reset-USB and Reset-DVBs when the end of the AVC boot- Reset-DVBs when the end of the AVC boot-...
Page 23
Service Modes, Error Codes, and Fault Finding Q551.1E LA EN 23 Constraints taken into account: - Display may only be started when valid LVDS output clock can be delivered by the AVC. - To have a reliable operation of the EEFL backlight, the backlight should be driven with a maximum PWM duty cycle during the first seconds.
Page 24
EN 24 Q551.1E LA Service Modes, Error Codes, and Fault Finding Semi Standby The assumption here is that a fast toggle (<2s) can only happen during ON->SEMI ->ON. In these states, the AVC is still active and can provide the 2s delay. If the transition ON->SEMI- >STBY->SEMI->ON can be made in less than 2s, Wait until previous on-state is left more than 2 seconds ago.
Page 25
Service Modes, Error Codes, and Fault Finding Q551.1E LA EN 25 Active Mute all sound outputs via softmute Wait 100ms Set main amplifier mute (I/O: audio-mute) Force ext audio outputs to ground (I/O: audio reset) And wait 5ms switch off Ambilight Wait until Ambilight has faded out: Output power Observer should be zero Switch off POK line...
Page 26
EN 26 Q551.1E LA Service Modes, Error Codes, and Fault Finding Semi Stand by If ambientlight functionality was used in semi-standby (lampadaire mode), switch off ambient light (see CHS ambilight) *) If this is not performed and the set is Delay transition until ramping down of ambient light is switched to standby when the switch off of finished.
Page 27
Introduction The error code buffer contains all detected errors since the last ComPair (Computer Aided Repair) is a Service tool for Philips time the buffer was erased. The buffer is written from left to Consumer Electronics products. and offers the following: right, new errors are logged at the left side, and all other errors 1.
Page 28
EN 28 Q551.1E LA Service Modes, Error Codes, and Fault Finding • Via the blinking LED procedure. See section 5.5.3 How to content, as this history can give significant information). This to Clear the Error Buffer. ensure that old error codes are no longer present. •...
Page 29
Service Modes, Error Codes, and Fault Finding Q551.1E LA EN 29 LAYER 2 error = 28 will be logged and displayed via the 2. Two short blinks of 250 ms followed by a pause of 3 s blinking LED procedure if SDM is switched on. 3.
Page 30
EN 30 Q551.1E LA Service Modes, Error Codes, and Fault Finding Fault Finding and Repair Tips +12V is considered OK (=> DETECT2 signal becomes "high", +12V to +1V8, +12V to +3V3, +12V to +5V DC-DC converter can be started up) if it rises above 10V and doesn’t drop below Read also section “5.5 Error Codes,...
Page 31
Service Modes, Error Codes, and Fault Finding Q551.1E LA EN 31 Then push the “SOURCE” button for 10 seconds until the “F” disappears from the screen. 5.8.6 Logging When something is wrong with the TV set (f.i. the set is rebooting) you can check for more information via the logging in Hyperterminal.
Page 32
Before starting: - prepare a USB memory stick with the latest software - download the latest Main Software (Fus) from www.p4c.philips.com - unzip this file - create a folder ”upgrades” in the root of a USB stick (size > 50 MB) and save the autorun.upg file in this "upgrades"...
Page 33
Service Modes, Error Codes, and Fault Finding Q551.1E LA EN 33 Set is st art in g u p in F act o ry m o d e Set is starting up in F actory m ode? Noisy picture with bands/lines is visible and the An “F”...
Page 34
How to start the software upgrade application manually: 1. Disconnect the TV from the Mains/AC Power. 5.9.5 UART logging 2K10 (see section “5.8 Fault Finding and 2. Press the “OK” button on a Philips TV remote control or a Repair Tips, 5.8.6 Logging) Philips DVD RC-6 remote control (it is also possible to use a TV remote in “DVD”...
Alignments Q551.1E LA EN 35 6. Alignments Index of this chapter: For the next alignments, supply the following test signals via a 6.1 General Alignment Conditions video generator to the RF input: 6.2 Hardware Alignments • EU/AP-PAL models: a PAL B/G TV-signal with a signal 6.3 Software Alignments strength of at least 1 mV and a frequency of 475.25 MHz 6.4 Option Settings...
Page 36
EN 36 Q551.1E LA Alignments Table 6-3 White D alignment values - LED - Minolta CS-200 Table 6-10 White tone default setting 46" (Rubens) Value Cool (11000K) Normal (9000K) Warm (6500K) White Tone e.g. 46PFL9705x/xx 0.276 0.287 0.313 Colour Temp 0.282 0.296 0.329...
Page 37
Alignments Q551.1E LA EN 37 6.4.2 Dealer Options 6.5.1 SSB identification For dealer options, in SAM select “Dealer options”. Whenever ordering a new SSB, it should be noted that the See Table 6-12 SAM mode overview. correct ordering number (12nc) of a SSB is located on a sticker on the SSB.
Page 38
EN 38 Q551.1E LA Alignments Total Overview SAM modes Table 6-12 SAM mode overview Main Menu Sub-menu 1 Sub-menu 2 Sub-menu 3 Description Hardware Info A. SW version e.g. “Q5521_0.33.0.0 Display TV & Stand-by SW version and CTN serial number B.
Page 39
Alignments Q551.1E LA EN 39 Main Menu Sub-menu 1 Sub-menu 2 Sub-menu 3 Description Options Digital broadcast Off/On Select DVB On/Off DVB - T installation Off/On or Country dependent Select DVB T installation On/Off or by country DVB - T light Off/On Select DVB T light On/Off DVB - C...
Page 40
EN 40 Q551.1E LA Alignments Main Menu Sub-menu 1 Sub-menu 2 Sub-menu 3 Description Option numbers Group 1 e.g. “00008.01793.15421.08192” The first line (group 1) indicates hardware options 1 to 4 Group 2 e.g. “44013.34315.00000.00000” The second line (group 2) indicates software options 5 to 8 Store Store after changing...
Circuit Descriptions Q551.1E LA EN 41 7. Circuit Descriptions Index of this chapter: Introduction 7.1 Introduction 7.2 Power Supply The Q551.1E LA is a new chassis launched in Europe in 2010. 7.3 Backlight Concept The whole range is covered by PNX8550x main IC so-called 7.4 DC/DC Converters NXP TV550 platform.
Page 42
EN 42 Q551.1E LA Circuit Descriptions 18750_201_100415.eps 100415 Figure 7-2 Architecture of TV550 platform (200 Hz) back to 2010-Jun-25 div. table...
Page 43
Circuit Descriptions Q551.1E LA EN 43 7.1.3 SSB Cell Layout N -D VBS C onnector N -D VBS 8981x LVD S 8957x D C /D C T uner C las s -D P N X 85500 8951 x 8950 x 89 94 x 6451 x 8952 x...
Page 44
EN 44 Q551.1E LA Circuit Descriptions AL C PLD T C O N S harp 9073x 90711 x passthr ough F GPA passthrough D C /D C T uner C las s- D P N X 85500 8951 x 8950 x 899 4x 6450 x 8952 x...
Page 45
Circuit Descriptions Q551.1E LA EN 45 AL C PLD T C O N LG D 9073x 9069 x passthr ough F GPA passthrough D C /D C T uner C las s- D P N X 85500 8951 x 8950 x 899 4x 6406 x 8952 x...
Page 46
7.2.2 Diversity specifications! This part is available in the regular market. Consult the Philips Service web portal for the order codes of the The diversity in power supply units is mainly determined by the boards. diversity in displays. Refer to the Spare Parts list for the correct order number.
Page 47
Circuit Descriptions Q551.1E LA EN 47 7.2.3 Connector overview T co n 1 0 0H z B a ckL ig h t Table 7-1 Connector overview D ire ctL E D S h a rp Connector sca n n in g 1308 1311 1M95...
Page 48
The C-balance drivers and -components are mounted on a 2D-D I M separate C-balancer board. This PWB is mounted on the LCD 1G5 1 panel by the LCD manufacturer, though developed by Philips. There are two possible configurations: • For edge-lit displays & direct-lit displays + “0D” dimming...
Page 49
Circuit Descriptions Q551.1E LA EN 49 • +V-LNB, input voltage for LNB supply IC (item no. 7T50) • +5V-DVBS, input intermediate supply voltage for DVB-S2 + 24V + 5V + 5V + 3V 3 tuner + 5V + 3V 3 (diagram B08A) 537.1 m A 777.4 m A...
Page 50
EN 50 Q551.1E LA Circuit Descriptions 18770_236_100127.eps 100219 Figure 7-20 Front-End block diagram Brazil region Front-End DVB-S(2) reception The Front-End for the DVB-S(2) application consist of the following key components: • Satellite Tuner; I C address 0xC6 (bridged via channel decoder) 18770_243_100203.eps •...
Page 51
Circuit Descriptions Q551.1E LA EN 51 and vivid colour management. High flat panel screen combination with LED backlights for optimum contrast and resolutions and refresh rates are supported with formats power savings up to 50%. including 1366 × 768 @ 100Hz/120Hz and 1920 × 1080 @ 100Hz/120Hz.
Page 52
EN 52 Q551.1E LA Circuit Descriptions Back-End back-end processor and has to be replaced entirely when defective (no component level repair). This board is not described in this manual. In some sets, a so-called “200 Hz” board is mounted together with the LCD panel.
Page 53
Circuit Descriptions Q551.1E LA EN 53 The communication between PNX85500, Complex Programmable Logic Device (CPLD) and the Ambilight module 3B34 uses the SPI protocol; refer to figure 7-27 Communication +3V3 +3V3 100K protocol outside LED board. Between the CPLD and the LED +3V3 driver, as “extra”...
Page 55
Circuit Descriptions Q551.1E LA EN 55 In p u t c o n n e c to r O p e n in g L E D d riv e r Te m p e ra tu re 1 M 8 3 fo r c lip s e n s o r L E D...
Page 56
EN 56 Q551.1E LA Circuit Descriptions LVDS M in i- T im in g C o n tro lle r IC S p re a d Input S D R A M LVDS S p e c tru m Output 1 6 bit R 1 A ~E D a ta...
Page 57
Circuit Descriptions Q551.1E LA EN 57 7.11.1 TCON Programming For LGD - TCONs, the EEPROM can be programmed via ComPair (via I C communication). For Sharp - TCONs, the data can be flashed with a “SPI Programmer” (via SPI communication). This device has to be ordered separately.
EN 58 Q551.1E LA IC Data Sheets 8. IC Data Sheets This chapter shows the internal block diagrams and pin electrical diagrams (with the exception of “memory” and “logic” configurations of ICs that are drawn as “black boxes” in the ICs).
Page 59
IC Data Sheets Q551.1E LA EN 59 Diagram B01 820400089943 Tuner, HDMI & CI, LM75BDP (IC 7FD1) Block diagram LM75B BIAS POINTER CONFIGURATION REFERENCE REGISTER REGISTER TEMPERATURE COUNTER BAND GAP REGISTER 11-BIT TEMP SENSOR SIGMA-DELTA A-to-D TIMER REGISTER CONVERTER OSCILLATOR COMPARATOR/ THYST INTERRUPT...
Page 60
EN 60 Q551.1E LA IC Data Sheets Diagram B02 820400089506 PNX85500, PNX85500 (IC7S00) Block diagram PNX8550x MEMORY CONTROLLER TS input MPEG SYSTEM CI/CA LVDS for PRIMARY TS out/in for PROCESSOR flat panel display PCMCIA VIDEO LVDS (single, dual or OUTPUT quad channel) DVB-T/C channel decoder...
Page 61
IC Data Sheets Q551.1E LA EN 61 Diagram B03 820400089514 CLASS D, TPA3120D2PWP (IC7D10) Block diagram TPA3120D2 0.22 F 22 H 470 F ROUT 0.68 F PGNDR 0.68 F PGNDL LOUT BYPASS 22 H 470 F AGND 0.22 F PVCCL AVCC PVCCR VCLAMP...
Page 62
EN 62 Q551.1E LA IC Data Sheets Diagram B03 820400089514 CLASS D, TPS53126PW (IC7U03) Block diagram Pinning information VBST1 DRVH1 DRVL1 PGND1 VFB1 TRIP1 VREG5 TEST1 V5FILT TEST2 TRIP2 VFB2 PGND2 DRVL2 DRVH2 VBST2 18310_300_090319.eps 100416 Figure 8-5 Internal block diagram and pin configuration back to 2010-Jun-25 div.
Page 63
IC Data Sheets Q551.1E LA EN 63 Diagram B03 820400089514 CLASS D, ST1S10PH (IC 7UD0) Block diagram Pinning information DFN8 (4 × 4) PowerSO-8 I_18010_083.eps 100402 Figure 8-6 Internal block diagram and pin configuration back to 2010-Jun-25 div. table...
Page 64
EN 64 Q551.1E LA IC Data Sheets Diagram B03 820400089514 CLASS D, LD1117DT25 (IC 7UD2) Block diagram LD1117DT Pinning information DPAK F_15710_166.eps 100402 Figure 8-7 Internal block diagram and pin configuration back to 2010-Jun-25 div. table...
Page 65
IC Data Sheets Q551.1E LA EN 65 Diagram B04 820400089524 Analog I/O, LAN8710A-EZKH (IC 7E10) Block diagram MODE0 HP Auto-MDIX Auto- 10M Tx MODE1 MODE Control Negotiation Logic Transmitter TXP / TXN MODE2 Reset Transmit Section RXP / RXN nRST Control 100M Tx 100M...
Page 66
EN 66 Q551.1E LA IC Data Sheets Diagram B04 820400089524 Analog I/O, SII9287B (IC 7EC1) Block diagram Pinning information 18770_303_100217.eps 100217 Figure 8-9 Internal block diagram and pin configuration back to 2010-Jun-25 div. table...
Page 67
IC Data Sheets Q551.1E LA EN 67 8.10 Diagram B04 820400089524 Analog I/O, TPA6111A2DGN (IC 7EE1) Block diagram IN 1− − BYPASS IN 2− − SHUTDOWN Bias Control Pinning information D OR DGN PACKAGE (TOP VIEW) IN1− BYPASS IN2− SHUTDOWN 18770_309_100217.eps 100217 Figure 8-10 Internal block diagram and pin configuration...
Page 68
EN 68 Q551.1E LA IC Data Sheets 8.11 Diagram B07 820400089604 DVBS FE, STV6110AT (IC 7R02) Block diagram RF_OUT RF_IN PLL, dividers DC offset compensation XTAL_IN C bus interface Amplifier XTAL_INN XTAL_OUT 18770_304_100217.eps 100217 Figure 8-11 Internal block diagram and pin configuration back to 2010-Jun-25 div.
Page 69
IC Data Sheets Q551.1E LA EN 69 8.12 Diagram B08 820400090982 DVBS Supply, TPS54283PWP (IC 7T03) Block diagram BOOT1 CLK1 Level PVDD1 Shift Current ) + DC(ofst) Comparator DRAIN1 DRAIN1 Overcurrent Comp 0.8 V COMP SLOPE1 MAX1 Weak Soft Start CLK1 Pull-Down Anti-Cross...
Page 72
EN 72 Q551.1E LA IC Data Sheets 8.15 Diagram B11 820400090695 TCON LGD, TPS62110RSA (IC 7JH1) Block diagram Undervoltage Vina Lockout Thermal Shutdown Comparator 1-MHz (COMP) Oscillator P-Channel Comparator Driver Shoot-Through Control Sawtooth Logic Logic Generator N-Channel SKIP Comparator Compensation The internal feedback divider is disabled and the FB pin is directly connected to the internal GM amplifier.
Circuit Diagrams and PWB Layouts Q551.1E LA EN 86 10. Circuit Diagrams and PWB Layouts 10-1 AL1 820400089786 AmbiLight Common LiteOn LED Common 1 LiteOn 15 LED Common AL1A AL1A 1M83 C1 +3V3 2B00 E8 2B11 2B01 F8 2B02 E9 100n 2B03 I14 FH12-25S-0.5SH(55)
Page 87
Circuit Diagrams and PWB Layouts Q551.1E LA EN 87 LiteOn LED Common 2 LiteOn 15 LED Common 2 AL1B AL1B 2B50 C11 3B50 B7 +24V 3B51 B7 7B50-1 3B52 B7 BC847BS(COL) 3B53-1 B7 3B53-2 C7 3B53-3 C7 FB70 3B53-4 C7 PWM-B2 3B50 +24V...
Page 88
Circuit Diagrams and PWB Layouts Q551.1E LA EN 88 10-2 AL1 820400089793 2 LED 50% LiteOn LiteOn 2 LED 50% LiteOn 2 LED 50% AL6A AL6A 1M84 C13 3C01-1 B2 3C01-2 B2 3C01-3 C2 3C01-4 C2 3C07-1 3C02-3 D2 3C02-4 E2 3C07-2 3C05-1 C7 +24V...
Circuit Diagrams and PWB Layouts Q551.1E LA EN 97 10-8 AL1 820400089712 21 LED LiteOn 21 LED LiteOn 21 LED LiteOn AL3A AL3A 1M84 7203 7204 7205 LTW-008RGB LTW-008RGB LTW-008RGB SPI-CLOCK-BUF SPI-DATA-OUT2 Blue BLUE BLUE BLUE SPI-DATA-RETURN +24V GREEN GREEN GREEN Green PWM-CLOCK-BUF...
Page 98
Circuit Diagrams and PWB Layouts Q551.1E LA EN 98 21 LED LiteOn 21 LED LiteOn AL3B AL3B 2E10 D13 2F10 H13 3E02-1 C2 3E02-2 C2 3E02-3 B2 3E02-4 B2 3E05-3 D2 3E05-4 D2 3E10 B13 +24V 3E11 C13 3E12 C13 7E01-1 3E13-1 C13 BC847BS(COL)
Page 99
Circuit Diagrams and PWB Layouts Q551.1E LA EN 99 21 LED LiteOn 21 LED LiteOn AL3C AL3C 2D04-1 C7 2D04-2 C7 2D04-3 C8 2D04-4 C7 2D10 G14 2D11 B9 3D00-1 B7 3D00-2 C7 +3V3 3D00-3 C7 2D11 3D00-4 B7 100n 3D02-1 E2 7D26-1 3D02-2 E2...
Page 135
Circuit Diagrams and PWB Layouts Q551.1E LA EN 135 PNX Digital Video In PNX Digital Video In B02C B02C 2S2E F5 3S0W E5 7S00-6 D6 IS01 E6 IS10 E7 7S00-6 PNX85500 HDMI_DV HDMIA-RX2+ RX0_A HDMIA-RX2- HDMIA-RX1+ HDMIA-RX1- RX1_A DDCA-SCL DDC_A DDCA-SDA HDMIA-RX0+ IS10...
Page 144
Circuit Diagrams and PWB Layouts Q551.1E LA EN 144 PNX Digital Video In PNX Digital Video In B02C B02C 2S2E F5 3S0W E5 7S00-6 D6 IS01 E6 IS10 E7 7S00-6 PNX85500 HDMI_DV HDMIA-RX2+ RX0_A HDMIA-RX2- HDMIA-RX1+ RX1_A HDMIA-RX1- DDCA-SCL DDC_A DDCA-SDA HDMIA-RX0+ IS10...
Need help?
Do you have a question about the 8000 Series and is the answer not in the manual?
Questions and answers