Related Manuals for Cressi DIGI 2
Summary of Contents for Cressi DIGI 2
- Page 1 DIGI 2 Manuale d’uso User Manual Manuel d’utilisation Manual de uso Benutzerhandbuch 用户手册 Manual do usuário...
-
Page 2: Table Of Contents
IMPORTANT RECOMMENDATIONS: ..........23 READING INFORMATION ON THE SCREEN ........25 INTRODUCTION AND MAIN FEATURES ..........26 What the DIGI 2 console is not: ............26 What the DIGI 2 console is: ............. 26 HOW TO CONNECT THE DIGI 2 CONSOLE ......... 26 HOW TO ACTIVATE THE DIGI 2 CONSOLE ......... -
Page 3: Important Recommendations
Cressi Sub S.p.A. recommends using the DIGI 2 Diving in areas with particularly poor visibility console only after having read and understood this instruction manual. could make it difficult or impossible to read the DIGI 2 console. Avoid diving in these conditions. WARNING! Cressi Sub S.p.A. - Page 4 WARNING! Only use breathable air that meets the requirements of UNI EN 12021. IMPORTANT! Do not exceed the equipment operating limits. The pressure gauge is certified for use at pressure no greater than 300 bar. The maximum operating pressure of the gauge is shown on the back of the instrument.
-
Page 5: Reading Information On The Screen
READING INFORMATION ON THE SCREEN CURRENT CYLINDER PRESSURE (set in BAR or PSI) CURRENT DEPTH (set in m or ft) RANGE Battery status indicator (see BATTERY chapter) DIVE TIME (minutes) of the previous dive or TEMPERATURE (set in C° or F°). This information appears in rotation on the screen. -
Page 6: Introduction And Main Features
Congratulations, guarantee accurate monitoring of tank pressure, depth, dive time, and Cressi Sub S.p.A. congratulates you on your purchase of a DIGI 2 other information helpful to the diver. console, a complete and sophisticated device designed in our Research and Design Department and manufactured in Cressi Sub S.p.A. -
Page 7: How To Activate The Digi 2 Console
Do not dive if the DIGI 2 is not correctly connected to a pressurized scuba unit. LAUNCH SEQUENCE AFTER ACTIVATION Immediately after it is activated, the DIGI 2 console will run the launch sequence, during which it will display, in order: Switch on all segments... -
Page 8: Dive Screen
DIVE SCREEN If the DIGI 2 console is active, the dive will begin once a depth of 1.2 1 second meters is exceeded. WARNING! Do not dive with the smart cover inserted into the display housing! Removing it at depth would cause the instrument... -
Page 9: Surface Screen (Post-Dive)
5 seconds When the dive is complete, two minutes after reaching the surface (depth < 0.8 m), the DIGI 2 console switches back to surface mode (see chapter SURFACE SCREEN [PRE-DIVE]). Thus it will show the following information:... -
Page 10: Automatic Display Switch-Off
” on with the rest of the display off: in this condition the battery is not able to ensure the proper operation of the DIGI 2 console. For this reason the display does “ ” off: the instrument has optimum power not show any information and all functions are disabled. - Page 11 WARNING! Keep in mind that planning one or more dives in cold water, or any time that the DIGI 2 console spends outside during the winter or inclement weather, will result in reduced battery power. Therefore, consider replacing it in advance as a precaution, or carry a ready battery replacement kit in case of need.
-
Page 12: Changing The Battery
Gently insert a pointed object (a small flat-head screwdriver) into Use a coin of appropriate thickness to unscrew the battery the cavity, and carefully and delicately lever up the used battery. compartment cover on the back of the DIGI 2 console. - Page 13 When the test concludes, the DIGI 2 console will provide a response regarding the battery change that was just performed: PASS. The test was positive; the battery change was effective. Change the CR2450 battery, taking care to position the new one the same way, with the positive pole facing outward without reclosing the cap.
- Page 14 WARNING! If you should notice any humidity on the inside of the glass, immediately bring the DIGI 2 console to an authorized Cressi center. It is strictly forbidden to disassemble the console or its components; doing so will immediately void the warranty.
-
Page 15: Smart Cover" Functions
DIGI 2 if it has not been correctly connected and activated (HOW TO CONNECT THE DIGI 2 CONSOLE and HOW TO ACTIVATE THE DIGI 2 CONSOLE). WARNING! -
Page 16: Changing The Unit Of Measure
When the DIGI 2 console is switched on, turn it off by resting the smart cover against it, respecting the orientation in the figure. Remove the smart cover. -
Page 17: Changing Colored Protected Cover
CHANGING COLORED PROTECTED COVER The DIGI 2 console is covered by a silicone shell that gives the product its special look while also protecting it from accidental blows. Users or an authorized center can replace the shell by following these steps: •... -
Page 18: Maintaining The Digi 2 Console
It is strictly prohibited to replace the hose originally During storage and transport, the high-pressure hose should not be assembled on the DIGI 2 console with another of a different type or overly forced in the stowage with folds exceeding a 4 cm radius. -
Page 19: Technical Information
An original Cressi Sub S.p.A. battery kit is available, complete Requests for repair under warranty will be satisfied free of charge by with all components to be replaced. Cressi Sub or by a Cressi Sub authorized service center, according to • BACKLIGHTING: The DIGI 2 console features a their sole judgment, and the product will be repaired or replaced photoluminescent display. -
Page 20: Regulatory References
UNI EN 13319:2000 regarding Depth Gauges and Combined and address, and enclose the purchase receipt or invoice. Depth and Time Measuring Devices. You can find your authorized Cressi Sub center by asking your dealer PRODUCT DISPOSAL or Cressi Sub S.p.A. itself by sending an e-mail to: Consider the device to be electronic waste. - Page 21 Via Gelasio Adamoli, 501 - 16165 - Genova - Italia Tel. +39 010 830.79.1 - Fax +39 010 830.79.220 info@cressi.com • www.cressi.com rev_02_2019...
Need help?
Do you have a question about the DIGI 2 and is the answer not in the manual?
Questions and answers