Advertisement
Quick Links
Advertisement
Related Manuals for Taga Harmony HTA-25B
Summary of Contents for Taga Harmony HTA-25B
- Page 1 HTA-25B HYBRID INTEGRATED AMPLIFIER VU M ET ER Instruction Manual...
- Page 2 World of tubes and the World of transistors. TAGA Harmony HTA-25B is a 25W / 4ohm high-fidelity but still affordable hybrid integrated amplifier utilizing two 6P1 and two 6N1 tubes in the preamp section and transistors at the output.
-
Page 3: Table Of Contents
Contents Safety Instructions Important Safety Instructions Front and Rear Panel Hooking up speaker cables Hooking up the amplifier Operation Additional Information Specifications... -
Page 4: Safety Instructions
Safety Instructions IMPORTANT READ THIS SECTION CAREFULLY BEFORE PROCEEDING! WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT REMOVE CHASSIS (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The triangle containing a lightning symbol is intended to alert the user to the presence of uninsulated dangerous voltages within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. -
Page 5: Important Safety Instructions
Important Safety Instructions 1. Read Instructions – All the safety and operating instruc- 13. Overloading - Do not overload wall outlets, extensions tions should be read before the product is operated. cords, or integral convenience receptacles as this cas 2. Retain Instructions – The safety and operating instruc- result in a risk of fire or electric shock. -
Page 6: Front And Rear Panel
Front and Rear Panel Front Panel: Power Switch (ON and OFF) and Power Status Indicator (around the Power Switch) USB Stick Input Headphone ¼” Jack Output USB and Bluetooth Knob (Play/Pause, Next/Previous) Input Selector (USB, CD, Bluetooth, AUX) USB/Bluetooth Input Status Led Indicator VU Meter Treble Regulator Bass Regular... -
Page 7: Hooking Up Speaker Cables
Hooking Up Speaker Cables The Speaker Connectors can accommodate up to 10AWG speaker cables as well as most of popular plugs (banana etc.). A 10AWG cable is recommended for longer connections (longer than 20 meters / 66 feet). For shorter lengths you can use 12/14 or 18 AWG cables. - Page 8 Hooking up the Amplifier Make sure the amplifier is turned off (the Power Switch is in the top position and the Power Cable is removed). Turn the Volume Regulator to MIN (max counter clockwise). Using speaker cables (not supplied with this product) connect your speakers to SPEAKERS OUT connectors located on the rear of the amplifier(check “Hooking Up Speaker Cables”...
-
Page 9: Operation
Operation Plug the Power Cable to the amplifier and into the electrical outlet. Turn on the amplifier – press the Power Switch (the Power Switch should be in the down position The status LED around the Power Switch should turn orange in a few seconds. If it does not, it means that the amplifier is working under an abnormal condition (a protection mode) –... - Page 10 Operation Bluetooth® Connection: After the amplifier is switched on - the built-in Bluetooth® receiver is waiting to be paired with a Bluetooth® source. Select BT input by rotating the Input selector knob – the USB/Bluetooth Input Status Led Indicator will start flashing. Select Bluetooth®...
-
Page 11: Additional Information
Volume / Bass and Treble regulations). Additional Information Break-In Your TAGA Harmony amplifier sounds great immediately after it is taken out of the carton but as all hybrid amplifiers, this amplifier requires a “break-in” period to reach its full sonic capabilities. - Page 12 Additional Information Turn off procedure Make sure to turn off the amplifier first when powering down your system. Note! If the amplifier was turned off even for a short period of time, you should wait at least 2 minutes before turning it back on. Do not turn it ON then OFF and then ON again in quick succession.
-
Page 13: Specifications
Specifications Power Output: 2 x 18W RMS / 8ohm 2 x 25W RMS / 4ohm Class A/B Vacuum Tubes: 2 x 6P1, 2 x 6N1 THD: Less or equal 0.5% (1kHz 1W) Signal/Noise ratio: ≥80dB Frequency Response: 20Hz – 20kHz Inputs: Analog: RCA stereo CD, AUX Digital: USB (MP3 / WMA / WAV / APE audio files) - Page 14 Notes...
- Page 15 Notes...
- Page 16 We strongly advise to contact a professional installer or dealer in order to install TAGA Harmony products. We recommend using high quality TAGA Harmony speaker cables and other installation accessories. Kit Content: Amplifier Power Cable Cotton Gloves 1PAIR Instruction Manual Your product is marked with the symbol as showed on the left.
Need help?
Do you have a question about the Harmony HTA-25B and is the answer not in the manual?
Questions and answers