Table of Contents
Advertisement
PO 4500007448 to PO 4500007457
USE THIS ADDENDUM FOR STEP 5.
UTILISEZ CET ADDENDA POUR L'ÉTAPE 5.
UTILICE ESTE APÉNDICE PARA LA ETAPA 5.
- PRE-DRILL A HOLE AT THE DESIRED HEIGHT USING A 3/16" DRILL BIT,
MAKING SURE IT IS ALIGNED TO A STUD.
- PERCEZ AU PRÉALABLE UN TROU À LA HAUTEUR SOUHAITÉE À L'AIDE D'UNE
MÈCHE DE 3/16", EN S'ASSURANT QU'IL EST ALIGNÉ À UN MONTANT.
- PERFORAR CON ANTELACIÓN UN AGUJERO EN LA ALTURA DESEADA Y
UTILIZANDO UNA BROCA DE 3/16". ASEGURARSE ELLO ES ALINEADO A UN VIGA.
STUD
MONTANT
VIGA
STUD
MONTANT
VIGA
STUD
MONTANT
VIGA
Advertisement
Table of Contents
Related Manuals for Tech Craft FLEX42W
Summary of Contents for Tech Craft FLEX42W
- Page 1 PO 4500007448 to PO 4500007457 USE THIS ADDENDUM FOR STEP 5. UTILISEZ CET ADDENDA POUR L'ÉTAPE 5. UTILICE ESTE APÉNDICE PARA LA ETAPA 5. - PRE-DRILL A HOLE AT THE DESIRED HEIGHT USING A 3/16" DRILL BIT, MAKING SURE IT IS ALIGNED TO A STUD. - PERCEZ AU PRÉALABLE UN TROU À...
- Page 2 LA MOULURE AVANT (IMC0246-BPWN) EST EN 3 PIÈCES: CHÂSSIS AVANT (IMC0246-BP), MOULURE AVANT GAUCHE (IMLFL0012-WN) ET MOULURE AVANT DROITE (IMLFR0012-WN) THE BACK PANEL IBACS0137-WGWG SHOULD BE IBACS0137-WNWN LE PANNEAU ARRIÈRE IBACS0137-WGWG DOIT ÊTRE IBACS0137-WNWN FLEX42W PO #4500007448 PO #4500007449 PO #4500007450 PO #4500007451 PO #4500007452...
- Page 3 5) A list of the part numbers of missing or damaged parts. OPTION / OPCIÓN 2 PAGES / PÁJINAS 8-9 FLEX42W WARRANTY AND FOR ANY REQUEST TO THE CUSTOMER SERVICE. GARANTIE ET POUR TOUTE DEMANDE AU SERVICE À LA CLIENTÈLE.
- Page 4 Si las manchas de huellas digitales, comida, bedida, etc. resultan dificiles de remover, use un paño húmedecido con una solución de detergente suave sin corrosivos. No utilice detergente en polvo, ningun material abrasico ò solvente. FLEX42W QTÉ CANT IMC0246-BPWG IBACS0137-WGWG PART NAME / NOM DE LA PIÈCE / NOMBRE DE LA PIEZA...
- Page 13 INSTALLATION : TECHCRAFT highly recommends that you use a qualified professional contractor to perform the entire installation. Do not use this product for any purpose other than that specified by TECHCRAFT. If you do not understand or comprehend these directions or have any doubts about the safety of the installation, please call a qualified contractor or contact TECHCRAFT at www.techcraft.net.
- Page 14 TOOL REQUIRED: Mallet, Power Drill, 3/16” drill bit, socket or wrench set, stud sensor, open wrench OUTILS REQUIS: Maillet, perceuse, mèche de 3/16”, jeu de clés à douille ou jeu de douilles, détecteur de montant, clé ouverte HERRAMIENTAS NECESSARIAS: Mazo, perforadora mecánica, broca de 3/16”, juego de llaves mecánicas o casquillos, detector de vigas, llave fija 1- The mounting frame must be mounted to two studs at least 12”...
- Page 15 TOOL REQUIRED: Mallet, Power Drill, 1/2" masonry bit, socket or wrench set, open wrench OUTILS REQUIS: Maillet, perceuse, mèche à béton de 1/2", jeu de clés à douille ou jeu de douilles, clé ouverte HERRAMIENTAS NECESSARIAS: Mazo, perforadora mecánica, broca a hormigón de 1/2", juego de llaves mecánicas o casquillos, llave fija 1- Use the mounting frame as a template to mark six (6) holes on the wall.
- Page 16 WARNING: DO NOT LAY THE TV FACE DOWN ON THE GLASS, lean it up against a wall or other solid surface. Laying the TV down on the glass may cause permanent damages. Place the rect. bracket hooks (IMC0077-BP) vertically as close to center of the TV as possible before installation. Thread bolts with your hand into your TV back.
Need help?
Do you have a question about the FLEX42W and is the answer not in the manual?
Questions and answers