Download
Share
Print this page
Ripmax WOT 4 Pro Mk2 Instruction Manual
  1. Manuals
  2. Brands
  3. Ripmax Manuals
  4. Toy
  5. WOT 4 Pro Mk2
  6. Instruction manual

Ripmax WOT 4 Pro Mk2 Instruction Manual

Criss foss design
Hide thumbs

Advertisement

Quick Links

Download this manual
A-CF002PRO

Advertisement

loading
Need help?

Need help?

Do you have a question about the WOT 4 Pro Mk2 and is the answer not in the manual?

Questions and answers

Related Manuals for Ripmax WOT 4 Pro Mk2

Summary of Contents for Ripmax WOT 4 Pro Mk2

  • Page 1 A-CF002PRO...
  • Page 2 Ripmax shall not be liable for any loss, consequential loss, damage will increase the risk of injury. Always keep yourself at a or expense arising from the improper use or operation in anyway.

  • Page 3: Wichtige Hinweise

    Achten Sie ebenfalls darauf, dass keine sonstigen Gegenstände Haftungsausschluss: mit sich drehenden Teilen in Berührung kommen! Denken Sie Ripmax Produkte sind häufig nur ein Teil einer ganzen auch an Ihre Haustiere! Funktionskette. Diese Funktionskette, wie auch die Einhaltung der Fliegen Sie grundsätzlich, ob mit Modellflugzeugen-, Montage und Betriebsanleitung als auch die Bedingungen und Hubschraubern- oder Multicoptern, nie in Augenhöhe...
  • Page 4 Wot4 Pro Instructions/Anleitung Chris Foss The Designer / Der Designer The fascination of flight captured Chris's imagination early on in his life when he started building, from kits and plans, simple free flight gliders and rubber powered models. By his early teens, Chris was already experimenting with his own designs, several of which have been featured as constructional plans in various...
  • Page 5 Wot4 Pro Instructions/Anleitung Introduction / Einführung Congratulations on your purchase of the Wot4 Pro ARTF! Supplied with a dedicated Irvine .39 the Pro is arguably the best Wot4 ever produced thanks to the lightweight structure and increased control surfaces. Take care to read these instructions through carefully before you start your build to familiarise yourself with the build process.
  • Page 6 Wot4 Pro Instructions/Anleitung Stage 1 / Schritt 1 The wings and ailerons are supplied with the hinges loose fitted, ready for installation. Remove both ailerons and insure that the hinges are inserted mid-way in their slots. Using thin cyano, pour a drop onto each hinge – above and below – ensuring the glue soaks into the hinge and surrounding wood on both ailerons.
  • Page 7 Wot4 Pro Instructions/Anleitung Stage 5 / Schritt 5 Carefully pull the lead through to the centre of the wing using the string. Pull out the servo connector through to the hole in the bottom of the wing then retain the servo lead with a short length of tape to stop the lead pulling back into the wing.
  • Page 8 Wot4 Pro Instructions/Anleitung Stage 10 / Schritt 10 Do not overtighten the control horn mounting screws as you don’t want to crush the aileron. Turn the model over and trim off any excess thread using side cutters. Nicht die Ruderhornschrauben überdrehen - Sie möchten ja nicht das Querruder zerdrücken.
  • Page 9 Wot4 Pro Instructions/Anleitung Stage 15 / Schritt 15 Adjust the pushrods to ensure that the ailerons are centred with the servos at their neutral position. Test to ensure that both ailerons move freely across their entire throw. Note that we have fitted short lengths of fuel tube over the clevis to ensure it cannot open under flight loads.
  • Page 10 Wot4 Pro Instructions/Anleitung Stage 20 / Schritt 20 Protect the covering with masking tape, then spread sufficient epoxy over the opposite panel joiner slot, wing joiner and root rib. Bring the two panels together ensuring the epoxy fills the join. Wipe off any excess that squeezes out of the joint, then use tape to hold the panels together as the adhesive cures.
  • Page 11 Wot4 Pro Instructions/Anleitung Stage 25 / Schritt 25 Locate the pre-bent tailwheel assembly and fit the tailwheel using the collet supplied. Nehmen Sie das vorgebogene Heckfahrwerk, und montieren das Spornrad mit dem mitgelieferten Stellring. Stage 26 / Schritt 26 Screw the tailwheel assembly in position with the tailwheel wire inline with the rear of the fuselage.
  • Page 12 Wot4 Pro Instructions/Anleitung Stage 30 / Schritt 30 Roughen the wire elevator joiner to increase the bond strength in the next step. Now loosely position the joiner at the rear of the tailplane slot. Using epoxy applied to the exposed wood, glue the tailplane into its slot.
  • Page 13 Wot4 Pro Instructions/Anleitung Stage 34 / Schritt 34 Using a sharp knife, carefully remove the film from the fuselage from just in front and behind the fin mounting slot as shown so that the fin has a completely film-free surface to bond to. Verwenden Sie ein scharfes Messer, und ziehen Sie vorsichtig die Folie vom Einbauschlitz im Rumpf ab, aber nur so weit, damit die Finne, für eine bessere Haftung, eine folienfreie Oberfläche...
  • Page 14 Wot4 Pro Instructions/Anleitung Stage 39 / Schritt 39 Insert two hinges into the rudder, ensuring they are located mid-way in their slots. Using thin cyano, pour a couple of drops onto each hinge - above and below - ensuring the glue soaks into the hinge and the surrounding wood.
  • Page 15 Wot4 Pro Instructions/Anleitung Stage 44 / Schritt 44 Fit the rubber grommets and ferrules to your elevator, rudder and throttle servos. Install the servos in the plywood radio tray, noting the orientation of the outputs as shown. Befestigen Sie die Gummiösen und Messinghülsen an Ihren Servos für Höhen- und Seitenruder und Gas.
  • Page 16 Wot4 Pro Instructions/Anleitung Stage 49 / Schritt 49 Screw a clevis onto the threaded end of the elevator pushrod so that the rod goes through the clevis by 2mm. Slide on a tube retainer and connect the clevis to the elevator horn as shown. Schrauben Sie einen Gabelkopf auf das Gewindeende des Höhenrudergestänges, so dass das Gestänge 2mm durch den Gabelkopf geht.
  • Page 17 Wot4 Pro Instructions/Anleitung Stage 54 / Schritt 54 The engine mount supplied with the Wot4 Pro is a two part design. Offer the engine up to one of the mounts, moving the engine forwards or backwards until the front of the prop driver is exactly 100 mm in front of the rear face of the mount.
  • Page 18 Wot4 Pro Instructions/Anleitung Stage 59 / Schritt 59 Locate the throttle pushrod outer sleeve. Install the tube with a drop of cyano to secure. Finden Gasdurchführung. Befestigen Plastikröhrchen mit einem Tropfen Sekundenkleber. Stage 60 / Schritt 60 Trim off the excess length of tube inside the radio bay as shown.
  • Page 19 Wot4 Pro Instructions/Anleitung Stage 64 / Schritt 64 With the servo centred tighten the clamp screw to secure the throttle pushrod and then adjust the high end and low throttle position on your transmitter. Mit dem zentrierten Servo schrauben Sie das Gasgestänge mit der Spannschraube fest.
  • Page 20 Wot4 Pro Instructions/Anleitung Stage 69 / Schritt 69 Now bolt the silencer to the engine with the spacer between the silencer and engine as shown. Nun schrauben Sie den Schalldämpfer, mit dem Abstandshalter zwischen dem Dämpfer und Motor, am Motor fest, wie gezeigt. Stage 70 / Schritt 70 Connect the fuel line to the engine then the pressure line to the exhaust and block the remaining fill line.
  • Page 21 Wot4 Pro Instructions/Anleitung Stage 74 / Schritt 74 Now fit the recommended I/C propeller (APC 11x4" for the Irvine 39) for the engine with the spinner. Your engine installation is now complete. Nun befestigen Sie den empfohlenen Propeller (APC 11x4 für den 6.3ccm Irvine Motor) am Motor mit Spinner.
  • Page 22 Wot4 Pro Instructions/Anleitung Balancing / Schwerpunkt The Centre of Gravity (C/G or Balance Point) should be 82mm (3-1/4") back from the leading edge of the wing at the root. This should be measured with the fuel tank empty. Support the completed model under the wing either side of the fuselage at this point and add weight or adjust the position of the radio battery in as necessary to achieve a slightly nose down attitudeand secure in place.
  • Page 23 Wot4 Pro Instructions/Anleitung Pre-Flight Checks / Vorflug Checks The Wot4 Pro is not a trainer as the structure is built to give a low weight for performance flying so requires extra care. Inspect the structure before you fly and transport carefully to avoid damage. Always fly the Wot4 in a safe location at a recognised club.
  • Page 24 Adresse, oder besuchen Sie unsere Webseite unter www.ripmax.de Spare parts are available for the Wot4 Pro all Ripmax stocked model shops. In case of any difficulty, any product queries, or to locate your local Ripmax stockist, please write to the address below or visit www.ripmax.com...