Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Tapco Mix.120
Summary of Contents for Tapco Mix.120
-
Page 2: Safety Instructions
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL ATTENTION: POUR EVITER LES RISQUES DE CHOC ELECTRIQUE, NE PAS ENLEVER LE COUVERCLE. -
Page 3: Table Of Contents
TAPCO LIMITED WARRANTY ... 23 Don’t forget to visit our website at www.tapcogear.com for more information about this and other TAPCO products. What me, read a manual? Before you begin, please make sure you read the Safety Instructions on page 2 and Getting Started on page 4. -
Page 4: Getting Started
9. Turn up the MAIN MIX control to the 9 o’clock position (for the Mix.50 and Mix.60) or to the –10 mark (for the Mix.100 and Mix.120), for now. We’ll crank it up later on. 10. Now you are ready to set the levels. -
Page 5: A Few Precautions
INPUT INPUT INPUT INPUT BAL/UNBA L/UNBAL BAL/UNBA L/UNBAL LINE LINE GAIN GAIN HIGH HIGH 12kH 12kH 2.5kH 2.5kHz 2.5kH 2.5kHz 80Hz 80Hz 75Hz 75Hz SEND SEND SEND SEND PEAK PEAK LEVEL LEVEL A FEW PRECAUTIONS: • Never listen to loud music for prolonged periods. -
Page 6: Introduction
INTRODUCTION Thank you for choosing a TAPCO MIX Series mixer. The TAPCO family of mixers hails back to the days of TAPCO Corporation, Greg Mackie’s fi rst company. TAPCO revolutionized the audio industry back in 1969 with the very fi rst 6-channel mixer specifi cally designed for keyboards and rock ‘N’ roll PA. -
Page 7: Hookup Diagrams
HOOKUP DIAGRAMS Small Club Gig Microphones 1 and 2 INPUT INPUT INPUT INPUT INPUT INPUT BAL/UNBA L/UNBAL BAL/UNBA BAL/UNBA L/UNBAL L/UNBAL MONO MONO LINE LINE BAL/UNBA L/UNBAL GAIN GAIN LINE HIGH HIGH 12kH 12kH 2.5kHz 2.5kH 2.5kH 2.5kHz 80Hz 80Hz Keyboard Computer set-up Microphone... -
Page 8: Mix Series Features
INPUT INPUT INPUT INPUT INPUT INPUT BAL/UNBA L/UNBAL BAL/UNBA BAL/UNBA L/UNBAL L/UNBAL LINE LINE GAIN GAIN MIX SERIES FEATURES CHANNEL INPUTS 1. MIC (MICROPHONE) INPUTS The MIX Series is equipped with one or more rugged, low-noise, phantom-powered microphone preamplifi ers, providing up to 50 dB of crystal-clear amplifi... -
Page 9: Unity Gain
fi ltering it out makes the low stuff you do want much more crisp and tasty. 9. +4/–10 Switch (Mix.100/Mix.120 only) This switch changes the input sensitivity of the channel to match either the –10 dBv consumer level or the +4 dBu professional level. -
Page 10: Aux Return Section
For the Mix.50, Mix.100, and Mix.120, connect the aux return signal to the inputs of an unused stereo channel. This has the added benefi t of providing a level control for the aux return signal. - Page 11 T/OUTPUT SEND SEND PEAK LEVEL Mix.120 Main Section 16. TAPE TO CTRL RM/PHONES Switch (TAPE TO PHONES on Mix.50) Use this switch to select the signal source for the CONTROL ROOM outputs, PHONES, and METERS. When the switch is up, they all receive the main mix signal tapped after the MAIN MIX control.
-
Page 12: Main Section
MAIN SECTION 18. POWER LED This LED turns on when the mixer’s power cord is plugged into an AC outlet. Since there is no power switch on the MIX Series mixers, the mixer is always on when it is connected to AC power. 19. -
Page 13: Phones Output
Typically (providing the GAIN is set correctly), this will be positioned somewhere between 0 dB (U) and the 3 o’clock position. On the Mix.100 and Mix.120, this is a slide control (fader). Typically, the fader will be positioned somewhere between 0 dB (U) and the +5 dB position. -
Page 14: Rear Panel Features
upon the position of the TAPE TO CTRL RM/ PHONES (16) switch and the FX TO CTRL ROOM (17) switch. Note: Be very careful because the PHONES jack can drive any standard headphones to very loud levels. Please see page 2 for information on hearing protection. -
Page 15: Appendix A: Service Information
Details concerning Warranty Service are spelled out in the Warranty section on page 23. If you think your TAPCO mixer has a problem, please do everything you can to confi rm it before calling for service. Doing so might save you from the deprivation of your mixer and the associated suff... -
Page 16: Appendix B: Connections
APPENDIX B: CONNECTIONS XLR Connectors The Mic/Line Channels use 3-pin female XLR connectors on the MIC inputs. They are wired as follows, according to standards specifi ed by the AES (Audio Engineering Society). XLR Balanced Wiring: Pin 1 = Shield Pin 2 = Hot (+) Pin 3 = Cold (–) 1/4"... -
Page 17: Appendix C: Mix Series Specifications
Equalization Mono Channel EQ (Mix.50 only): High ±15 dB @ 12 kHz ±15 dB @ 80 Hz Mono Channel EQ (Mix.60, Mix.100, Mix.120) Stereo Channel EQ (Mix.60): High ±15 dB @ 12 kHz ±15 dB @ 2.5 kHz ±15 dB @ 80 Hz... - Page 18 The TAPCO Mix mixers were recently accidentally awarded fi rst prize by the Society of Juicers, Mixers and Blenders in the “Quadruple Planetary Mixers” category.
-
Page 19: Block Diagram Mix.50
Block Diagram Mix.50... -
Page 20: Block Diagram Mix.60
Block Diagram Mix.60... -
Page 21: Block Diagram Mix.100
Block Diagram Mix.100... -
Page 22: Block Diagram Mix.120
Block Diagram Mix.120... -
Page 23: Tapco Limited Warranty
B. Failure to register online or return the product registration card will not void the one-year warranty. C. Service and repairs of TAPCO products are to be performed only at a factory-authorized service center. Unauthorized service, repairs, or modifi cation will void this warranty.
Need help?
Do you have a question about the Mix.120 and is the answer not in the manual?
Questions and answers
добрый день . можно ли сделать эффект эха на микшере tapco mix 120. спасибо