Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for BAUKER PSJ750G2
Summary of Contents for BAUKER PSJ750G2
- Page 1 PSJ750G2 750W JIG SAW WITH LASER GUIDE ORIGINAL INSTRUCTION MANUAL...
-
Page 3: General Power Tool Safety Warnings
GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings, instructions, illustrations and specifications provided with this Important - Please read these instructions fully before starting assembly power tool. Failure to follow all instructions listed below may General Power Tool Safety Warnings result in electric shock, fire and/or serious injury. - Page 4 e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. Important - Please read these instructions fully before starting assembly f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) General Power Tool Safety Warnings protected supply.
- Page 5 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off.
-
Page 6: Jig Saw Safety Warnings
JIG SAW SAFETY WARNINGS 1. Hold reciprocating saw by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. - Page 7 6. CAUTION: Use of controls or adjustments other than those specified herein may result in hazardous radiation exposure. Additional safety warning for class 2 laser The laser device fitted to this tool is CLASS 2 with a maximum radiation of XXXmW and XXXnm wavelength. CLASS 2 LASER RADIATION, DO NOT STARE INTO BEAM EN-7...
- Page 8 EN-8...
- Page 9 EN-9...
- Page 10 EN-10...
- Page 11 SYMBOLS To reduce the risk of injury, user must read instruction manual Wear eye protection Wear ear protection Wear dust mask Warning Double insulation Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice. Do not stare into beam Laser radiation EN-11...
-
Page 12: Component List
18. SAW BLADE (SEE FIG. D) 19. SDS PLATE SPANNER (SEE FIG. H1) Not all the accessories illustrated or described are included in standard delivery. TECHNICAL DATA Type PSJ750G2 (PSJ-designation of machinery, representative of Jig Saw) Rated voltage: 230-240V~ 50Hz Rated power 750W... -
Page 13: Noise Information
ACCESSORIES Wood cutting blade Metal cutting blade Vacuum adapter Parallel guide hex key We recommend that you purchase your accessories listed in the above list from the same store that sold you the tool. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice. - Page 14 This tool may cause hand-arm vibration syndrome if its use is not adequately managed WARNING: To be accurate, an estimation of exposure level in the actual conditions of use should also take account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle but not actually doing the job.
- Page 15 in position. Ensure the edge of the blade is located in the groove of the blade guide. To remove a blade, press the blade holder and then lift out the blade. Warning: blade teeth are very sharp. For best cutting results ensure you use a blade suited to the material and cut quality you need.
-
Page 16: Working Hints For Your Jig Saw
13. USING THE LASER GUIDE (SEE FIG. K) Never stare directly into the laser beam and never point the beam at anybody. The laser beam energy is extremely harmful to your eyes. 1. The laser generator is for the purpose of precision cutting, and projects a visible red line on the workpiece surface, make your mitre cut along the red line. -
Page 17: Metal Cutting
the workpiece and plunge the saw blade slowly into the workpiece. As soon as the complete surface of the base plate rests on the work piece, continue to saw along the cutting line. (See Fig L, M) METAL CUTTING Use a finer tooth blade for ferrous metals and a coarse tooth blade for non-ferrous metals. When cutting thin sheet metals always clamp wood on both sides of the sheet to reduce vibration or tearing of the sheet metal. - Page 18 PLUG REPLACEMENT (ONLY FOR REWIRABLE PLUG OF UK & IRELAND) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: BLUE – NEUTRAL BROWN –...
-
Page 19: Declaration Of Conformity
Positec Power Tools (Europe) Ltd, PO Box 6242, Newbury, RG14 9LT, UK Declare that the product Jig Saw Description PSJ750G2 (PSJ-designation of machinery, representative of Jig Saw) Type Sawing various materials Function Complies with the following Directives, 2006/42/EC, 2011/65/EU, 2014/30/EU...
Need help?
Do you have a question about the PSJ750G2 and is the answer not in the manual?
Questions and answers